1. Home
    2. /
  2. Manuals
    3. /
  3. Allied-Data
    4. /
  4. CopperJet-1616-2P
    5. /
  5. 6
Page 26 / 86 Scroll up to view Page 21 - 25
Chapter 5: Configuring the CopperJet
5.6.2
Configuring RFC1483 Routed service attached to the Router
A RFC 1483 Routed connection is used when your Service Provider delivers a routed
connection between the CopperJet and the Service Provider Network.
You need to add detailed configuration information about the WAN service that you are
creating. This information must be provided by your service provider.
Description
:
RFC1483, this is the default WAN connection name.
VPI
:
Virtual Path Identifier. A field in the ATM header. The VPI is
used to identify the virtual path that a circuit belongs to.
The VPI can be any value between 0 and 4095.
VCI
:
Virtual Channel Identifier. Part of the ATM header. The VCI
is a tag that identifies which channel a cell will travel over.
The VCI can be a value between 1 and 65535.
Encapsulation:
LLC/SNAP. Ethernet over LLC/Snap. This is the default
setting of RFC1483.
Use DHCP:
When your ISP automatically allocates an IP address, use
this option.
WAN IP address:
Select this option when you have a fixed WAN IP address.
This IP address is provided by your ISP.
Unnumbered
:
Disabled by default.
Default Gateway
:
When you use the option WAN IP address, you must fill in
the default gateway.
Enable NAT
:
NAT is by default enabled.
When finished configuring the WAN connection, click on
OK.
Go to the
Configuration
menu
and click on
Save config
to save the new settings into the CopperJet.
Page 24
Page 27 / 86
Chapter 5: Configuring the CopperJet
5.6.3
Configuring RFC1483 Bridged service attached to the Router
RFC1483 Bridged service attached to the Router is mostly used when you have a bridged
line, but you want to have more then 1 pc on the internet (sharing).
You need to add detailed configuration information about the WAN service that you are
creating. This information must be provided by your service provider.
Description
:
RFC1483, this is the default WAN connection name.
VPI
:
Virtual Path Identifier. A field in the ATM header. The VPI is
used to identify the virtual path that a circuit belongs to.
The VPI can be any value between 0 and 4095.
VCI
:
Virtual Channel Identifier. Part of the ATM header. The VCI
is a tag that identifies which channel a cell will travel over.
The VCI can be a value between 1 and 65535.
Encapsulation:
LLC/SNAP. Ethernet over LLC/Snap. This is a bridge
connection method and is the default setting of RFC1483.
Default MAC Address:
Use the MAC address of the CopperJet on the WAN side.
MAC address:
Fill in the MAC address that you want to use on the WAN
side.
Use DHCP:
When your ISP automatically allocates an IP address, use
this option.
WAN IP address:
Select this option when you have a fixed WAN IP address.
This IP address is provided by your ISP.
Default Gateway
:
When you use the option WAN IP address, you must fill in
the default gateway.
Enable NAT
:
NAT is by default enabled.
When finished configuring the WAN connection, click on
OK.
Go to the
Configuration
menu
and click on
Save config
to save the new settings into the CopperJet.
Page 25
Page 28 / 86
Chapter 5: Configuring the CopperJet
5.6.4
Configuring IPoA routed service attached to the Router
An IPoA routed connection is used when your Service Provider delivers a routed connection
between the CopperJet and the Service Provider Network.
You need to add detailed configuration information about the WAN service that you are
creating. This information must be provided by your service provider.
Description
:
IPoA, this is the default WAN connection name.
VPI
:
Virtual Path Identifier. A field in the ATM header. The VPI is
used to identify the virtual path that a circuit belongs to.
The VPI can be any value between 0 and 4095.
VCI
:
Virtual Channel Identifier. Part of the ATM header. The VCI
is a tag that identifies which channel a cell will travel over.
The VCI can be a value between 1 and 65535.
Use DHCP:
When your ISP automatically allocates an IP address, use
this option.
WAN IP address:
Select this option when you have a fixed WAN IP address.
This IP address is provided by your ISP.
WAN IP mask:
Fill in the WAN IP mask.
Default Gateway
:
When you use the option WAN IP address, you must fill in
the default gateway.
Enable NAT
:
NAT is by default enabled.
When finished configuring the WAN connection, click on
OK.
Go to the
Configuration
menu
and click on
Save config
to save the new settings into the CopperJet.
Page 26
Page 29 / 86
Chapter 5: Configuring the CopperJet
5.6.5
Configuring PPPoA routed service attached to the Router
PPPoA routed is mostly used when your Service Provider has an ATM network which
requires authentication (username and password).
You need to add detailed configuration information about the WAN service that you are
creating. This information must be provided by your service provider.
Description
:
PPPoA, this is the default WAN connection name.
VPI
:
Virtual Path Identifier. A field in the ATM header. The VPI is
used to identify the virtual path that a circuit belongs to.
The VPI can be any value between 0 and 4095.
VCI
:
Virtual Channel Identifier. Part of the ATM header. The VCI
is a tag that identifies which channel a cell will travel over.
The VCI can be a value between 1 and 65535.
Encapsulation:
Auto by default.
Authentication
:
Choose the authentication method provided by your service
provider.
None
:
You don’t need to set any authentication.
PAP
:
Password Authentication Protocol. The server sends an
authentication request to the remote user that is dialling in.
PAP passes the unencrypted username and password and
identifies the remote end.
CHAP
:
Challenge Handshake Authentication Protocol The server
sends an authentication request to the remote user that is
dialling in. CHAP passes the encrypted username and
password and identifies the remote end.
Username
:
Fill in the username provided by your service provider.
Page 27
Page 30 / 86
Chapter 5: Configuring the CopperJet
Password
:
Fill in the password provided by your service provider.
Password (confirm)
:
Fill in the password provided by your service provider.
Keep Alive
:
On by default. Some ISP’s time-out if the connection has
not been used. To avoid it, you can enable keep-alive that
keeps the connection by accessing an Internet site at
regular intervals.
Connect on demand
:
Off by default. When enabled, the PPP link will be
established when traffic is sent to the Service Provider and
disconnected when traffic has stopped for a certain amount
of time. See also the Maximum Idle Time.
Maximum idle time
:
0 by default. When
Connect On demand
is enabled, this
time represents the idle time when the PPP link will be
disconnected.
Requested WAN IP address
:
Fill in 0.0.0.0 when you get an IP address after
authentication, or fill in a fixed IP address provided by your
service provider.
Enable NAT
:
NAT is by default enabled.
When you are finished with configuring the WAN connection, click on
OK.
Go to the
Configuration
menu and click on
Save config
to save the new settings into the CopperJet.
Page 28

Rate

4.5 / 5 based on 2 votes.

Popular Allied-Data Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top