Page 41 / 156
Scroll up to view Page 36 - 40
3FE-61830-AAAA-TCZZA
Alcatel-Lucent
5-1
Edition 01
May 2008
5
Wizard
Overview
Purpose
The CellPipe 7130 RG configuration wizard enables speedy and accurate configuration
of the CellPipe 7130 RG and Internet connection. The following sections describe the
configurable connection parameters. Each parameter has a default setting that is suitable
for most situations; however, you may modify these to suit your network environment.
Contents
This chapter covers the following topic:
To use the configuration wizard
5-1
To use the configuration wizard
When to use
This procedure describes how to use the configuration wizard to quickly set up the
CellPipe 7130 RG with the minimum required configurations.
Before you begin
When subscribing to a broadband service, you must know the method by which you are
connected to the Internet; your WAN device can be Ethernet, DSL, or both. Technical
Page 42 / 156
Wizard
To use the configuration wizard
5-2
Alcatel-Lucent
3FE-61830-AAAA-TCZZA
Edition 01
May 2008
information regarding the properties of your Internet connection should be provided by
your ISP. For example, your ISP should instruct you:
•
whether you are connected to the Internet using a static or dynamic IP address
•
which protocols, such as PPPoA or PPPoE, you must use to communicate over the
Internet
Please collect the following information from your ISP:
VPI
VCI
Encapsulation: VC-MUX or
LLC
Protocol
Standard
Username/Password
Password protocol
Procedure
1
Select
Wizard
in the CellPipe 7130 RG menu bar to open the Wizard menu.
This menu
is available only for the admin user.
Caution
Possible service interruption
Do not change the VPI/VCI values unless instructed to do so by your ISP.
2
Select
Wizard
in the Wizard menu to open the Wizard window. In this window you can
configure the VPI and VCI for your ATM PVC.
Be sure to use the VPI and VCI numbers assigned to you. The valid range for VPI is 0 to
255 and for VCI is 32 to 65535 (0 to 31 is reserved for local management of ATM
traffic).
Page 43 / 156
To use the configuration wizard
Wizard
3FE-61830-AAAA-TCZZA
Alcatel-Lucent
5-3
Edition 01
May 2008
Figure 5-1
Wizard window
3
Click
Next
. The Connection Type window appears. In this window you can select the
WAN Connection Type and the Encapsulation Mode as provided to you by your ISP.
Figure 5-2
Connection Type window
The following table describes the fields of the Connection Type window. Choose the
parameters that match the information provided by your ISP and click
Next
.
Page 44 / 156
Wizard
To use the configuration wizard
5-4
Alcatel-Lucent
3FE-61830-AAAA-TCZZA
Edition 01
May 2008
Table 5-1
Field descriptions
Field
Description
WAN Connection Type
The WAN Connection Type, one of:
•
PPPoA
•
PPPoE
•
1483 MER
•
1483 Routed
•
1483 Bridged
Encapsulation Mode
The method of encapsulation used by your
ISP, one of:
•
LLC/SNAP
•
VC-Mux
a.
If you selected PPPoA or PPPoE as the connection type, go to step 4.
b.
If you selected 1483 MER as the connection type, go to step 8.
c.
If you selected 1483 Routed as the connection type, go to step 10.
d.
If you selected 1483 Bridged as the connection type, go to step 11.
PPPoA and PPPoE configuration
4
If you selected PPPoA or PPPoE for the WAN Connection Type, configure the following
settings in the PPP configuration windows for the CellPipe 7130 RG type.
Page 45 / 156
To use the configuration wizard
Wizard
3FE-61830-AAAA-TCZZA
Alcatel-Lucent
5-5
Edition 01
May 2008
Figure 5-3
WAN IP Settings window
The following table describes the fields of the WAN IP Settings window.
Table 5-2
Field descriptions
Field
Description
Obtain an IP address automatically
The dynamic IP is not fixed; your ISP
assigns a different IP address each time you
connect to the network.
Use the following IP address
Specify a fixed IP address that is provided
by your ISP.
WAN IP address
The static IP address of the WAN interface
provided by your ISP, in dotted decimal
notation.
Enable NAT
Select the check box to enable the NAT
functions of the CellPipe 7130 RG. NAT
must be enabled if the CellPipe 7130 RG is
functioning as a router.
5
Click
Next
. The PPP Username and Password window appears. Set the field values
according to the information provided by your ISP.
19216811.live