2Wire 5012NV-002 Router Manual PDF (Setup & Configuration Guide)

Page 86 / 128 Scroll up to view Page 81 - 85

Configuring Firewall Settings

78

HomePortal 3801HGV Gateway User Guide

Configuring Firewall Settings

14.

Modify the information as per your requirement.

15.

Click

Add to List

. The configuration changes appear in the

Definition List

section of the

same page.

16.

Repeat step 8 to 15 for each port or range of ports required for the application profile.

Page 87 / 128

Configuring Firewall Settings

79

HomePortal 3801HGV Gateway User Guide

Configuring Firewall Settings

Deleting User-defined Applications

To delete a user defined application:

1.

Click

Edit or delete user-defined application

in the

Edit firewall settings for this computer

section. This lets you delete an existing profile. The

Edit or Delete a User-Defined

Application

page appears.

2.

Select the application you want to delete from the

User defined applications

list box.

3.

Click

Delete

. The configuration successful prompt confirms the deletion. You cannot view

the deleted application in the

User defined applications

list box.

Allowing all Applications

To allow all applications through firewall:

1.

On the

Allow device application traffic to pass through firewall

page,

select

Allow all

applications (DMZplus mode)

radio button. This will enable DMZplus mode.

DMZplus is used for hosting applications when hosted applications do not function

properly. When in DMZplus mode, the designated computer appears as if it is directly

connected to the Internet, has all unassigned TCP and UDP ports opened and pointed to it,

Page 88 / 128

Disabling Attack Detection

80

HomePortal 3801HGV Gateway User Guide

Configuring Firewall Settings

and can receive unsolicited network traffic from the Internet.The DMZplus mode

configuration page appears:

2.

Click

Save

.

3.

Confirm that the computer you selected is configured for DHCP

. If it is not, configure it for

DHCP

.

4.

Restart the computer. When the computer restarts, it receives a special IP address from

the system and all unassigned TCP and UDP ports are forwarded to it.

m

Use the DMZplus mode with caution. A computer in the DMZplus mode is less secure

because all available ports are open and all incoming Internet traffic is directed to this

computer.

Disabling Attack Detection

Objective

To disable a specific port in the attack detection section.

By default, attack detection is enabled on these ports by the firewall. However, some applications

and devices may require the use of specific data ports listed here. The gateway allows users to

open the necessary ports through the firewall.

Page 89 / 128

Disabling Attack Detection

81

HomePortal 3801HGV Gateway User Guide

Configuring Firewall Settings

Steps

1.

Navigate to

Settings

>

Firewall

>

Advanced Configuration

. The

Advanced Configuration

page to configure

Attack Detection

appears.

2.

Clear the

Excessive Session Detection

check box.

When disabled, the firewall does not detect applications on the local network that are

creating excessive sessions to the Internet. This activity is due to a virus infected

computer and on detection, the gateway displays a HURL warning page.

3.

Clear the

TCP/UDP Port Scan

check box.

When disabled, the firewall does not detect UDP and TCP port scans, and communicates

the port scan packets to the computer.

A port scan is a series of messages sent by an external entity attempting to break into a

computer to learn which computer network services associated with UDP and TCP ports

are provided by the computer.

4.

Clear the

Invalid Source/Destination IP address

check box.

When disabled, the firewall does not verify IP addresses for: Broadcast or multicast IP

addresses, TCP destination IP address is not unicast, IP source and destination address

are the same, Invalid IP source received from private/home network.

5.

Clear the

Packet Flood (SYN/UDP/ICMP/Other)

check box.

When disabled, the firewall does not check for SYN, UDP

, ICMP

, and other types of packet

floods on the local and Internet facing interfaces.

6.

Clear the

Invalid TCP Flag Attacks (NULL/XMAS/Other)

check box.

When disabled, the firewall does not scan inbound and outbound packets for invalid TCP

Flag settings, and communicates the packet that could result in NULL/XMAS/Other type of

attacks.

7.

Clear the

Invalid ICMP Detection

check box.

When disabled, the firewall does not check for invalid ICMP/code types, and

communicates the associated packets to the computer.

8.

Clear the

Miscellaneous

check box.

When disabled, the firewall does not scan any other type of inbound and outbound packets,

other than the ones listed in the

Attack Detection

section.

9.

Click

Save

. The ports listed in the

Attack Detection

section are disabled.

Page 90 / 128

Controlling Inbound and Outbound Traffic

82

HomePortal 3801HGV Gateway User Guide

Configuring Firewall Settings

Controlling Inbound and Outbound Traffic

Objective

To control inbound and outbound protocol control services, so that the firewall blocks or passes the

traffic from/to the network to/from the Internet.

Steps

1.

Navigate to

Settings

>

Firewall

>

Advanced Configuration

. The

Advanced configuration

page to configure the outbound and inbound protocols appears:

2.

Select or clear any check box in the

Outbound Protocol Control

section. If you select any of

the check boxes in the

Outbound Protocol Control

section, the firewall allows the traffic

from the network to pass through the firewall to the Internet.

3.

Select or clear any check box in the

Inbound Protocol Control

section. If you select any of

the check boxes in the

Inbound Protocol Control

section, the firewall allows the

corresponding protocol to pass from the Internet to the network.

4.

Click

Save

. This saves the configuration changes done to the inbound and outbound

protocol control.

Note

Allowing inbound traffic does not mean that the firewall automatically allows this type of

traffic to pass through the firewall to the network. Even if a particular protocol/application

type is allowed, the firewall still checks and blocks all unsolicited traffic from the Internet

unless the firewall is configured to pass the traffic by hosting an application profile.

Rate

Popular 2Wire Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share