www.netcomm.com.au

21

NetComm NP805N

–

Gigabit Wireless Router

YMLO-805N

Static IP

OPTION

DEFINITION

WAN IP Address

Enter the WAN IP address used for your connection.

WAN Subnet Mask

Enter the WAN Subnet mask used for your connection.

WAN Gateway

Enter the WAN Gateway address used for your connection.

Primary DNS

Ente r the Primary DNS used for your connection.

Secondary DNS

Enter the Secondary DNS (if available) used for your connection.

NAT

This option enables or disables "Network Address Translation" for this connection type.

Multicast

Enable multicast support for this connection. Select the appropriate IGMP protocol version from the pull down menu.

IGMP Snooping

This option enables or disables "IGMP" for this connection type.

NP805N

–

Gigabit Wireless Router

22

NetComm NP805N - Gigabit Wireless Router

YMLO-805N

www.netcomm.com.au

PPP over Ethernet

OPTION

DEFINITION

IPv6 Dualstack

Select to enable or disable the IPv6 Dualstack function for this connection type.

Username

The account name given to you by your ISP.

Password

The password given to you by your ISP.

Primary DNS

This feature allows you to manually assign a Primary DNS Server

(Optional - Refer to your ISP for more information)

.

Secondary DNS

This feature allows you to manually assign a Secondary DNS Server

(Optional - Refer to your ISP for more information)

.

Service Name

Enter the service name if your ISP requires it

(Optional - Refer to your ISP for more information)

.

Assigned IP Address

Enter the IP address assigned to your service. This is usually left blank.

MTU

The default MTU value is 0 (auto). It is set automatically when you connect.

NAT

This option enables or disables "Network Address Translation" for this connection type

Multicast

Enable multicast support for this connection. Select the appropriate IGMP protocol version from the pull down menu.

IGMP Snooping

This option enables or disables "IGMP" for this connection type.

www.netcomm.com.au

23

NetComm NP805N

–

Gigabit Wireless Router

YMLO-805N

PPTP

OPTION

DEFINITION

IP Mode

Select to use either a static or dynamically assigned IP address for your connection. When selecting to utilise a static IP

address, you will also need to enter the PPTP IP Address, PPTP Subnet Mask and PPTP Default gateway in use for the

connection

(Refer to your PPTP administrator for more information)

.

Server IP Address/Name

Enter the PPTP server name or IP Address.

PPTP Account

Enter the PPTP username supplied by your PPTP administrator.

PPTP Password

Enter the PPTP password supplied by your PPTP administrator.

Connection ID

Enter an Optional name to identify the PPTP connection.

Maximum Idle Time

The amount of inactivity on the internet connection before it is disconnected. Set it to zero or enable "Auto-reconnect" to

disable this feature.

Connection Control

There are 3 modes to select from:



Connect-on-demand: The NP805N will connect to the internet when a client sends outgoing packets.



Auto Reconnect (Always-on): The NP805N will automatically reconnect to the internet until the

connection is manually disconnected.



Manually: The NP805N will not connect to the internet until someone clicks the connect button in the

Status-page.

MTU

The default MTU value is 0 (auto). It is set automatically when you connect.

MPPE

Select to enable or disable the MPPE security extensions for the PPTP connection.

Multicast

Enable multicast support for this connection. Select the appropriate IGMP protocol version from the pull down menu.

IGMP Snooping

This option enables or disables "IGMP" for this connection type.

NP805N

–

Gigabit Wireless Router

24

NetComm NP805N - Gigabit Wireless Router

YMLO-805N

www.netcomm.com.au

L2TP

OPTION

DEFINITION

IP Mode

Select to use either a static or dynamically assigned IP address for your connection. When selecting to utilise a static IP

address, you will also need to enter the L2TP IP Address, L2TP Subnet Mask and L2TP Default gateway in use for the

connection

(Refer to your L2TP administrator for more information)

.

Server IP Address/Name

Enter the L2TP server name or IP Address.

L2TP Account

Enter the L2TP username supplied by your L2TP administrator.

L2TP Password

Enter the L2TP password supplied by your L2TP administrator.

Connection ID

Enter an Optional name to identify the L2TP connection.

Maximum Idle Time

The amount of inactivity on the internet connection before it is disconnected. Set it to zero or enable "Auto-reconnect" to

disable this feature.

Connection Control

There are 3 modes to select from:



Connect-on-demand: The NP805N will connect to the internet when a client sends outgoing packets.



Auto Reconnect (Always-on): The NP805N will automatically reconnect to the internet until the

connection is manually disconnected.



Manually: The NP805N will not connect to the internet until someone clicks the connect button in the

Status-page.

MTU

The default MTU value is 0 (auto). It is set automatically when you connect.

MPPE

Select to enable or disable the MPPE security extensions for the L2TP connection.

Multicast

Enable multicast support for this connection. Select the appropriate IGMP protocol version from the pull down menu.

IGMP Snooping

This option enables or disables "IGMP" for this connection type.

www.netcomm.com.au

25

NetComm NP805N

–

Gigabit Wireless Router

YMLO-805N

DHCP Server

This Page allows you to change the Dynamic Host Configuration Protocol (DHCP) server settings on the NP805N. The DHCP

Server enables computers or devices connecting to the NP805N to automatically obtain their network configuration settings. By

default, the DHCP server is enabled.

OPTION

DEFINITION

DHCP Server

Enable or disable the DHCP server.

IP Pool Starting/Ending Address

Whenever there is a request, the DHCP server will automatically allocate an unused IP address from the IP address pool

to the requesting computer. You must specify the starting / ending address of the IP address pool

Lease Time

Length of the DHCP lease time

Domain Name

Optional, this information will be passed to the client

Click "Save" to save these settings or “Undo” to ca

ncel.

You can also check the DHCP client list by clicking the “Client List” button.

Please note:

See the section “DHCP Client List” below for more information

The “Fixed Mapping…” button allows you to map a specific IP address to a specific MAC

address.

Please note:

See the section “DHCP Fixed Mapping” below for more information

Click the "More…" button for the following extended options:

OPTION

DEFINITION

Primary DNS

Optional, this information will be passed to the client

Secondary DNS

Optional, this information will be passed to the client

Primary WINS

Optional, this information will be passed to the client

Secondary WINS

Optional, this information will be passed to the client

Gateway

Optional, this information will be passed to the client