Zyxel VSG1432-B101 Router Manual PDF (Setup & Configuration Guide)

Page 6 / 16 Scroll up to view Page 1 - 5

6

To connect your VSG1432-B101:

1.

Attach the antenna and point it up.

2

3

4

5

1

Page 7 / 16

VSG1432-B101 Series

7

2.

Do one of the following for your Internet connection:

a. DSL WAN

: Use a telephone cable to connect your VSG1432-

B101’s

DSL

port to a telephone jack (or the DSL or modem jack on

a splitter if you have one).

b. ETHERNET WAN

: If you already have a broadband router or

modem, use an Ethernet cable to connect the

ETHERNET WAN

port to it for Internet access.

3.

LAN

: Use an Ethernet cable to connect a computer to a

LAN

port for

initial configuration and/or Internet access.

4.

USB

: Connect a USB (version 2.0 or lower) memory stick or a USB

hard drive for file sharing. Use a USB extension cable if the stick is

too big to fit.

5.

POWER

: Use the provided power adaptor to connect the

POWER

socket to an appropriate power source. Make sure the power at the

outlet is on. After connecting the power adaptor, look at the lights on

the front panel.

•

The

POWER

light blinks while your VSG1432-B101 starts up and

then stays on once it is ready.

•

Each

LAN

light stays on if the corresponding

LAN

port is properly

connected and blinks when there is traffic.

•

The

ETHERNET

WAN

light stays on if the

ETHERNET

WAN

port is

properly connected and blinks when there is traffic.

•

The

USB

light turns on when your VSG1432-B101 detects a

connected USB device.

•

The

DSL WAN

light turns on when your VSG1432-B101 has a DSL

connection.

Page 8 / 16

8

•

The

WLAN / WPS

light flashes green and orange while WPS is in

process. It stays on green when the wireless LAN is ready and

blinks when there is traffic.

•

The

INTERNET

light turns on when the gateway is able to access

the Internet and will blink when your VSG1432-B101 is sending or

receiving data.

If the lights do not come on, check your connections and inspect your

cables for damage. If the lights are still off, contact technical support.

Page 9 / 16

VSG1432-B101 Series

9

Set Up a Wireless Network

You can set up a wireless network using the following methods:

Using Wireless Protected Setup (WPS)

Press the

WPS

button on the VSG1432-B101’s front panel for more than

5 seconds to turn the WPS function on.

Follow these steps to add a WPS-enabled device to the wireless network

using the

WPS/WLAN

button.

Place the devices you want to connect near

one another.

Press the WPS button on the VSG1432-

B101.

The

WPS

light blinks green and orange.

Press the WPS button on a compatible

device within 2 minutes of pressing the

button on the VSG1432-B101.

The

WPS

light on the VSG1432-B101

shines steadily when connected.

1

2

3

Page 10 / 16

10

Set Up a Wireless Network Manually

The wireless LAN on your VSG1432-B101 is enabled by default. To add

a wireless client to the network, use the settings found on the bottom

panel of your VSG1432-B101, which will look similar to the following

example:

Configure wireless devices that you want to connect to the wireless

network to use the same wireless settings as the VSG1432-B101.

The default wireless settings vary for each VSG1432-B101. Refer to the

bottom panel of your device and use the provided information.

Log into the Web Configurator

Your device may already be set up for Internet access. However, you

may want or need to log on to the VSG1432-B101 Web Configurator to

perform tasks:

•

Configure your Internet access settings manually

•

Customize the Quality of Service (QoS) and routing features

•

Create firewall and web filter rules

•

Edit remote management, as well as other features

SSID: ZyXEL00561

Security Mode: WPA-PSK

Pre-Shared Key: FB373BD356

Rate

Popular Zyxel Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share