Page 36 / 327
Scroll up to view Page 31 - 35
Chapter 4 Tutorials
VMG3926-B10A User’s Guide
36
8
You should see a summary of your new DSL connection setup in the
Broadband
screen as follows.
Try to connect to a website to see if you have correctly set up your Internet connection. Be sure to
contact your service provider for any information you need to configure the WAN screens.
4.3
Setting Up a Secure Wireless Network
Thomas wants to set up a wireless network so that he can use his notebook to access the Internet.
In this wireless network, the VMG serves as an access point (AP), and the notebook is the wireless
client. The wireless client can access the Internet through the AP.
Thomas has to configure the wireless network settings on the VMG. Then he can set up a wireless
network using WPS (
Section 4.3.2 on page 37
) or manual configuration (
Section 4.3.3 on page 41
).
4.3.1
Configuring the Wireless Network Settings
This example uses the following parameters to set up a wireless network.
1
Click
Network
Setting
>
Wireless
to open the
General
screen. Select
More Secure
as the
security level and
WPA2-PSK
as the security mode. Configure the screen using the provided
parameters (see
page 36
). Click
Apply
.
SSID
Example
Security Mode
WPA2-PSK
Pre-Shared Key
DoNotStealMyWirelessNetwork
802.11 Mode
802.11b/g/n Mixed
Page 37 / 327
Chapter 4 Tutorials
VMG3926-B10A User’s Guide
37
2
Go to the
Wireless >
Others
screen and select
802.11b/g/n
Mixed
in the
802.11 Mode
field.
Click
Apply
.
Thomas can now use the WPS feature to establish a wireless connection between his notebook and
the VMG (see
Section 4.3.2 on page 37
). He can also use the notebook’s wireless client to search
for the VMG (see
Section 4.3.3 on page 41
).
4.3.2
Using WPS
This section shows you how to set up a wireless network using WPS. It uses the VMG as the AP and
ZyXEL NWD210N as the wireless client which connects to the notebook.
Note: The wireless client must be a WPS-aware device (for example, a WPS USB adapter
or PCMCIA card).
Page 38 / 327
Chapter 4 Tutorials
VMG3926-B10A User’s Guide
38
There are two WPS methods to set up the wireless client settings:
•
Push Button Configuration (PBC)
- simply press a button. This is the easier of the two
methods.
•
PIN Configuration
- configure a Personal Identification Number (PIN) on the VMG. A wireless
client must also use the same PIN in order to download the wireless network settings from the
VMG.
Push Button Configuration (PBC)
1
Make sure that your VMG is turned on and your notebook is within the cover range of the wireless
signal.
2
Make sure that you have installed the wireless client driver and utility in your notebook.
3
In the wireless client utility, go to the WPS setting page. Enable WPS and press the WPS button
(
Start
or
WPS
button).
4
Push and hold the
WPS
button located on the VMG’s front panel for more than 5 seconds.
Alternatively, you may log into VMG’s web configurator and go to the
Network Setting >
Wireless >
WPS
screen. Enable the WPS function for method 1 and click
Apply
. Then click the
Connect
button.
Note: Your VMG has a WPS button located on its front panel as well as a WPS button in its
configuration utility. Both buttons have exactly the same function: you can use one
or the other.
Note: It doesn’t matter which button is pressed first. You must press the second button
within two minutes of pressing the first one.
1
2
3
Page 39 / 327
Chapter 4 Tutorials
VMG3926-B10A User’s Guide
39
The VMG sends the proper configuration settings to the wireless client. This may take up to two
minutes. The wireless client is then able to communicate with the VMG securely.
The following figure shows you an example of how to set up a wireless network and its security by
pressing a button on both VMG and wireless client.
Example WPS Process: PBC Method
PIN Configuration
When you use the PIN configuration method, you need to use both the VMG’s web configurator and
the wireless client’s utility.
1
Launch your wireless client’s configuration utility. Go to the WPS settings and select the PIN method
to get a PIN number.
2
Log into VMG’s web configurator and go to the
Network Setting > Wireless >
WPS
screen.
Enable the WPS function and click
Apply
.
Wireless Client
VMG
SECURITY INFO
COMMUNICATION
WITHIN 2 MINUTES
Press and hold for
5 seconds
WLAN/
WPS
Page 40 / 327
Chapter 4 Tutorials
VMG3926-B10A User’s Guide
40
3
Enter the PIN number of the wireless client and click the
Register
button. Activate WPS function on
the wireless client utility screen within two minutes.
The VMG authenticates the wireless client and sends the proper configuration settings to the
wireless client. This may take up to two minutes. The wireless client is then able to communicate
with the VMG securely.
The following figure shows you how to set up a wireless network and its security on a VMG and a
wireless client by using PIN method.
1
2
3
19216811.live