Page 26 / 162 Scroll up to view Page 21 - 25
17
24.
WAN Settings:
The ZyXEL VFG6005 Series VPN Firewall Gateway supports Ethernet WAN and Mobile WAN.
Ethernet WAN has three
connection types: DHCP, Static and PPPoE. Please ensure which connection type should be used, and select your internet
connection type from the pull-down menu.
Whatever WAN connection type you have chosen, The ZyXEL VFG6005 Series VPN Firewall Gateway will get a WAN IP
and this IP will be shown in the Router/Status page as below.
If ―Not Connected‖ shows up in the setting, you shoul
d check the WAN settings again to get correct connection
Page 27 / 162
18
5.1.1
DHCP (automatic IP address assignment)
The IP address is automatically assigned to you by your ISP. You will see the following screen when you choose DHCP.
WAN
Select Enable/Disable to enable/disable WAN
Connection Type
DHCP
Host Name
Some ISP and DHCP servers ask for the Host Name of the DHCP client before assigning an
IP address. In this case, please key in your Host Name.
MTU
Maximum Transmission Unit
5.1.2
Static (Fixed IP address assignment)
The IP address, subnet mask, gateway, and DNS server are provided by your ISP.
Please enter the information accordingly.
WAN
Select Enable / Disable to enable/disable WAN.
Connection Type
Static IP
External IP Address
The external IP addresses offered by the ISP.
Netmask
The netmask offered by the ISP.
Gateway
The gateway offered by the ISP.
Static DNS 1
The static DNS 1 offered by the ISP.
Page 28 / 162
19
Static DNS 2
The static DNS 2 offered by the ISP.
MTU
Maximum Transmission Unit
5.1.3
PPPoE (connected by username/password)
If your ISP provides the username and password, please enter the information accordingly.
WAN
Select Enable/Disable to enable/disable WAN
Connection Type
PPPoE
Authentication
The authentication type CHAP or PAP offered by your ISP.
User Name
The user name offered by the ISP.
Password
The password offered by the ISP.
PPP Connection Type
Always Connected will maintain the PPPoE dial up connection. On Demand will
connect only when there is traffic.
Max Idle Time
PPPoE On Demand will only be activated when there is traffic. When there is no
traffic within the max idle time (default: 300 seconds), the PPPoE connection will be
disconnected.
PPP Echo Interval
PPPoE echo will ensure whether the link is still up or not (default interval 20
seconds)
PPP Retry Threshold
When PPPoE echo retry exceeds PPPoE Retry Threshold (default 20 times), the
dial up connection would be recognized as down.
PPP MTU
PPPoE maximum transmission unit: up to 1492
bytes (PPPoE‘s header is 8
bytes)(This value should be less than MTU value at least 8 bytes ).
MTU
Physical Device Maximum Transmission Unit
Provided by
your ISP
Page 29 / 162
20
5.1.4
Ethernet WAN MAC Address Clone
Some ISPs only allow a registered MAC address to access to the internet. To bypass the rule, you need to set up a cloned
MAC address for The ZyXEL VFG6005 Series VPN Firewall Gateway using the pre-registered MAC address.
1.
Click on [Setup]
[MAC Address Clone] tab.
You will see the following screen.
2.
Configure your MAC Clone for Ethernet WAN, Mobile WAN and LAN following the instructions below.
Clone WAN MAC
If your ISP only grants access to a fixed MAC address, please select Enable.
If your ISP does not enforce access control, please select Disable.
MAC Address
If the PC you use to configure The ZyXEL VFG6005 Series VPN Firewall Gateway is
the device which has the right MAC address to access the internet, press ―Get My
MAC‖ button. You can also type in
the MAC Address which has been granted access
by your ISP.
5.1.5
Mobile WAN (connected by information related to what your ISP needs)
Please enable and enter the APN, PIN code, user name, and password provided by your ISP. You may also choose from
the list of profiles for well known ISP settings. (Please note that some information might not be needed.)
Page 30 / 162
21

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top