P-660HW-Dx v2 Quick Start Guide

6

4

If no ISP settings are detected, click next to go to the following screen. Enter your Internet connection

information exactly as provided by your ISP.

5

If you do not see this screen, or your ISP has given you Internet access settings not available on this

screen, see section

6

. If you wish to set up a wireless network, complete the

Internet/Wireless Setup

Wizard

before going to this section.

6

Next, select either

Obtain an IP Address Automatically

or

Static IP Address.

If you select

Static IP

Address

then fill out the required fields based on the information provided by your ISP and click

Apply

.

7

If the Internet connection test is successful, either browse to your favorite website or click

Next

on your

screen to go to section

5

to configure your wireless settings.

5 Configuring your

Wireless Settings

To create a wireless network, the P-660HW-Dx v2 and your wireless computer must all use the same SSID

(network name), channel and security settings.

If you do not set wireless security then anyone within range could use your P-660HW-Dx v2 to access your

network and the Internet.

Choose WPA-PSK wireless security if your wireless device supports it as it is stronger than WEP. Otherwise

choose WEP.

P-660HW-Dx v2 Quick Start Guide

7

1

Select

Active

and click

Next

to continue. It is strongly recommended that

Enable OTIST

is NOT selected.

See section

7

for more information.

2

Configure your wireless settings in the screen. Click

Next

.

3)

If you select either

WEP

or

WPA-PSK

security (recommended), then follow the directions to enter the

appropriate key. Click

Next

to continue and

Apply

to save your wireless LAN settings.

P-660HW-Dx v2 Quick Start Guide

8

4

Check your configuration and write down your wireless LAN settings for later use. Click

Finish

to complete and

save the wizard setup.

5

Your Internet is ready for you to use. Open your browser and navigate to your favorite website.

6 Internet Connection Setup Using Advanced Settings

Use this section to set up your Internet connection manually if you do not see the

ISP Parameters for Internet

Access

screen when you run the wizard (see section

4

, step

4

).

1

Login again. (Follow steps

1

to

5

in section

3

.)

2

Select

Go to Advanced setup

. Then, click

Apply

.

3

The

Status

screen appears. Click

Network

>

WAN

in the navigation panel on the left of the screen.

4)

Enter the information exactly as provided by your ISP. Click

Apply

.

P-660HW-Dx v2 Quick Start Guide

9

Note:

The fields available in this screen depend on the

Mode

and

Encapsulation

you select

5

If you still cannot access the Internet, see

Troubleshooting

and/or contact your Internet Service Provider

(ISP) for assistance.

7 Setting Up a Wireless Network with OTIST

7.1 About OTIST

ZyXEL's One-Touch Intelligent Security Technology (OTIST) feature allows you to automatically

configure the SSID and WPA-PSK on all OTIST-equipped wireless clients within range of the P-

660HW-Dx v2.

Enable OTIST only if your wireless clients support WPA and OTIST.

You should have already configured wireless settings on the

P-660HW-Dx v2 using the wizard.

If you select

Disable wireless security

using the wireless wizard, the P-660HW-Dx v2 will create a

WPA-PSK automatically.

If you select

Manually assign a WEP key

using the wireless wizard, the P-660HW-Dx v2 will replace

the WEP key with a WPA-PSK.

You must enable OTIST on the P-660HW-Dx v2 and all wireless clients within three minutes in any

order.

P-660HW-Dx v2 Quick Start Guide

10

7.2 Enabling OTIST

To enable OTIST on the P-660HW-Dx v2, you can either use the wizard (see section

3

) or hold in the

RESET

button (see section

1

) for about three seconds. Do not hold the

RESET

button in for too long, as this will reset

the P-660HW-Dx v2 to the factory defaults.

To enable OTIST on wireless clients, click

Start

in the

Adapter

screen. The

Setup Key

is 01234567 by default.

If you have previously saved a setup key on the P-660HW-Dx v2, use it instead of the default.

For more information, see

Wireless LAN

in the User's Guide.

Troubleshooting

1

If you cannot access the web configurator,

•

Your computer may be set to use a static IP address in a different subnet from the ZyXEL device. See the

appendix in the User’s Guide for information on setting up your IP address.

•

If you are using Internet Explorer in Windows XP or Windows Server 2003, make sure you allow pop-up

windows, JavaScripts and Java permissions or set the Internet security level lower than

High

in Internet

Explorer (in Internet Explorer, click

Tools > Internet Options > Security > Custom Level...

). See the

appendix in the User’s Guide for more information.

2

If you cannot access the Internet when your computer is connected to the

ETHERNET

port, follow these

steps.

A)

Check the lights on the front panel. If they are different from what is described in section

1

, make sure

the P-660HW-Dx v2 is correctly connected. (See section

1

.) If the lights are still different, turn off the

device, wait a few seconds, and turn it on again.

B)

Check you have correctly entered the informatinon your ISP gave you. For example, if your account has

a user name and password, make sure you type it correctly. In addition, if you are not sure which

encapsulation your ISP uses, contact your ISP. If your ISP did not give you Internet connection

information, follow the steps in section

2

.

C)

If you are using a new Internet account, contact your ISP to make sure it is active.

D)

If you still have problems, see

Troubleshooting

in the User’s Guide.

If you cannot access the Internet after you take the steps above, either try the following or contact your ISP:

E)

Turn your P-660HW-Dx v2 off and on. Open your Internet browser if it is not already open.

Let the P-660HW-Dx v2 complete the DSL connection test (this may take several minutes). See section

2

for

details.

If the test is successful, check whether you can access the Internet.

F)

If the test is unsuccessful or if you cannot access the Internet, log in to the P-660HW-Dx v2’s web

configurator (see section

3

).

• Click

Network

>

WAN

>

Internet Connection

. Ensure that the settings in this screen are the same as

those your ISP gave you. If your ISP gave you a static IP address to use, select

Static IP Address

in

the

IP Address

section and enter it in the

IP Address

field. If not, select

Obtain an IP Address Auto-

matically

. Click

Apply

.