1. Home
    2. /
  2. Manuals
    3. /
  3. Zyxel
    4. /
  4. P-2612HNU-F1F PLDT
    5. /
  5. 10
Page 46 / 424 Scroll up to view Page 41 - 45
Chapter 3 Tutorials
P-2612HNU-Fx User’s Guide
46
1
Open the ZyXEL utility and click the
Profile
tab to open the screen shown next.
Click
Add
to configure a new profile.
Tutorial: Profile
2
The
Add New Profile
screen appears. The wireless client automatically searches
for available wireless networks, and displays them in the
Scan Info
box. Click
Scan
if you want to search again. You can also configure your profile for a wireless
network that is not in the list.
Tutorial: Add New Profile
3
Give the profile a descriptive name (of up to 32 printable ASCII characters). Select
Infrastructure
and either manually enter or select the AP's SSID in the
Scan
Info
table and click
Select
.
Page 47 / 424
Chapter 3 Tutorials
P-2612HNU-Fx User’s Guide
47
4
Choose the same encryption method as the AP to which you want to connect (In
this example, WPA-PSK).
Tutorial: Profile Security
5
This screen varies depending on the encryption method you selected in the
previous screen. Enter the pre-shared key and leave the encryption type at the
default setting.
Tutorial: Profile Encryption
6
In the next screen, leave both boxes selected.
Tutorial: Wirele
s Protocol Se tings.
Page 48 / 424
Chapter 3 Tutorials
P-2612HNU-Fx User’s Guide
48
7
Verify the profile settings in the read-only screen. Click
Save
to save and go to the
next screen.
Tutorial: Confirm Save
8
Click
Activate Now
to use the new profile immediately. Otherwise, click the
Activate Later
button.
If you clicked
Activate Later
, you can select the profile from the list in the
Profile
screen and click
Connect
to activate it.
Note: Only one profile can be activated and used at any given time.
Tutorial: Activate
9
When you activate the new profile, the ZyXEL utility returns to the
Link Info
screen while it connects to the AP using your settings. When the wireless link is
established, the ZyXEL utility icon in the system tray turns green and the
Link
Info
screen displays details of the active connection.
10
Open your Internet browser, enter
or the URL of any other
web site in the address bar and press ENTER. If you are able to access the web
site, your new profile is successfully configured.
11
If you cannot access the Internet go back to the
Profile
screen, select the profile
you are using and click
Edit
. Check the details you entered previously. Also, refer
to the Troubleshooting section of this User's Guide or contact your network
administrator if necessary.
Page 49 / 424
Chapter 3 Tutorials
P-2612HNU-Fx User’s Guide
49
3.4
Setting Up NAT Port Forwarding
In this tutorial, you manage the Doom server on a computer behind the ZyXEL
Device. In order for players on the Internet (like
A
in the figure below) to
communicate with the Doom server, you need to configure the port settings and IP
address on the ZyXEL Device. Traffic should be forwarded to the port 666 of the
Doom server computer which has an IP address of 192.168.1.34.
Tutorial: NAT Port Forwarding Setup
You may set up the port settings by configuring the port settings for the Doom
server computer (see
Chapter 11 on page 204
for more information).
1
Click
Network
Setting
>
NAT
>
Port Forwarding
. Click
Add new rule
.
D
=192.168.1.34
WAN
LAN
port 666
A
Page 50 / 424
Chapter 3 Tutorials
P-2612HNU-Fx User’s Guide
50
2
Enter the following values:
3
Click
Apply
.
4
The port forwarding settings you configured should appear in the table. Make sure
the
Status
check box for this rule is selected. Click
Apply
to have the ZyXEL
Device start forwarding port 666 traffic to the computer with IP address
192.168.1.34.
Players on the Internet then can have access to your Doom server.
Service Name
Select
User Defined
.
WAN Interface
Select the WAN interface through which the Doom service is
forwarded. This is the default interface for this example, which is
MyDSLConnection
.
Start/End Ports
666
Translation Start/End
Ports
666
Server IP Address
Enter the IP address of the Doom server. This is
192.168.1.34
for this example.
Protocol
Select
TCP/UDP
. This should be the protocol supported by the
Doom server.

Rate

3.5 / 5 based on 2 votes.

Popular Zyxel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top