Zyxel P-2601HN-F1 Router Manual PDF (Setup & Configuration Guide)

Page 51 / 344 Scroll up to view Page 46 - 50

Chapter 3 Tutorials

P-2601HN(L)-F1 Series User’s Guide

51

3.7

Configuring Static Route for Routing to

Another Network

In order to extend your Intranet and control traffic flowing directions, you may

connect a router to the ZyXEL Device’s LAN. The router may be used to separate

two department networks. This tutorial shows how to configure a static routing

rule for two network routings.

In the following figure, router

R

is connected to the ZyXEL Device’s LAN.

R

connects to two networks,

N1

(192.168.1.x/24) and

N2

(192.168.10.x/24). If

you want to send traffic from computer

A

(in

N1

network) to computer

B

(in

N2

network), the traffic is sent to the ZyXEL Device’s WAN default gateway by

default. In this case,

B

will never receive the traffic.

You need to specify a static routing rule on the ZyXEL Device to specify

R

as the

router in charge of forwarding traffic to

N2

. In this case, the ZyXEL Device routes

N2

B

N1

A

R

Page 52 / 344

Chapter 3 Tutorials

P-2601HN(L)-F1 Series User’s Guide

52

traffic from

A

to

R

and then

R

routes the traffic to

B

.This tutorial uses the

following example IP settings:

To configure a static route to route traffic from

N1

to

N2

:

1

Click

Network Setting

> Routing

. Click

Add New Static Route

.

2

Configure the

Static Route Setup

screen using the following settings:

• Select

Active

.

•

Specify a descriptive name for this routing rule.

• Type

192.168.10.0

and subnet mask

255.255.255.0

for the destination,

N2

.

Table 3

IP Settings in this Tutorial

DEVICE / COMPUTER

IP ADDRESS

The ZyXEL Device’s WAN

172.16.1.1

The ZyXEL Device’s LAN

192.168.1.1

A

192.168.1.34

R

’s N1

192.168.1.253

R

’s N2

192.168.10.2

B

192.168.10.33

N2

B

N1

A

R

Page 53 / 344

Chapter 3 Tutorials

P-2601HN(L)-F1 Series User’s Guide

53

• Type

192.168.1.253

(

R

’s N1 address) in the

Gateway IP Address

field.

Click

Apply

. The

Routing

screen should display the route you just added.

Now

B

should be able to receive traffic from

A

. You may need to additionally

configure

B

’s firewall settings to allow specific traffic to pass through.

3.8

Configuring QoS Queue and Class Setup

This section contains tutorials on how you can configure the QoS screen.

Note: Voice traffic will not be affected by the user-defined QoS settings on the ZyXEL

Device. It always gets the highest priority.

Let’s say you are a team leader of a small sales branch office. You want to

prioritize e-mail traffic because your task includes sending urgent updates to

clients at least twice every hour. You also upload data files (such as logs and e-

mail archives) to the FTP server throughout the day. Your colleagues use the

Internet for research, as well as chat applications for communicating with other

branch offices.

In the following figure, your Internet connection has an upstream transmission

bandwidth of 10,000 kbps. For this example, you want to configure QoS so that e-

mail traffic gets the highest priority with at least 5,000 kbps. You can do the

following:

•

Configure a queue to assign the highest priority queue (7) to e-mail traffic from

the LAN interface, so that e-mail traffic would not get delayed when there is

network congestion.

•

Note the IP address (192.168.1.23 for example) and/or MAC address

(AA:FF:AA:FF:AA:FF for example) of your computer and map it to queue 7.

Page 54 / 344

Chapter 3 Tutorials

P-2601HN(L)-F1 Series User’s Guide

54

Note: QoS is applied to traffic flowing out of the ZyXEL Device.

Traffic that does not match this class is assigned a priority queue based on the

internal QoS mapping table on the ZyXEL Device.

1

Click

Network Setting > QoS > General

and check

Active

. Set your

WAN

Managed Upstream Bandwidth

to 10,000 kbps (or leave this blank to have the

ZyXEL Device automatically determine this figure). Click

Apply

to save your

settings.

Tutorial: Advanced > QoS

2

Go to

Network Setting > QoS > Queue Setup

. Click

Add new Queue

to create

a new queue. In the screen that opens, check

Active

and enter or select the

following values, then click

Apply

.

•

Name

: Email

•

Priority

: 7 (High)

•

Weight

: 15

10,000 kbps

DSL

E-mail: Queue 7

Your computer

IP=192.168.1.23

A colleague’s computer

Other traffic: Automatic classifier

and/or

MAC=AA:FF:AA:FF:AA:FF

Page 55 / 344

Chapter 3 Tutorials

P-2601HN(L)-F1 Series User’s Guide

55

•

Rate Limit

: 5,000 (kbps)

Tutorial: Advanced > QoS > Queue Setup

3

Go to

Network Setting > QoS > Class Setup

. Click

Add new Classifier

to

create a new class. Check

Active

and follow the settings as shown in the screen

below. Then click

Apply

.

Tutorial: Advanced > QoS > Class Setup

Class Name

Give a class name to this traffic, such as

Email

in this

example.

To Queue

Link this to a queue created in the

QoS > Queue

Setup

screen, which is the

Email

queue created in

this example.

Rate

Popular Zyxel Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share