1. Home
    2. /
  2. Manuals
    3. /
  3. Zyxel
    4. /
  4. NBG-418N
    5. /
  5. 4
Page 16 / 224 Scroll up to view Page 11 - 15
Chapter 1 Introduction
NBG-418N User’s Guide
16
allows one device to authenticate the other) in each of the two devices. When WPS is activated on
a device, it has two minutes to find another device that also has WPS activated. Then, the two
devices connect and set up a secure network by themselves.
For more information on using WPS, see
Section 5.2.1 on page 57
.
1.5
Wall Mounting
You may need screw anchors if mounting on a concrete or brick wall.
1
Select a position free of obstructions on a wall strong enough to hold the weight of the device.
2
Mark two holes on the wall at the appropriate distance apart for the screws.
Be careful to avoid damaging pipes or cables located inside the wall
when drilling holes for the screws.
3
If using screw anchors, drill two holes for the screw anchors into the wall. Push the anchors into the
full depth of the holes, then insert the screws into the anchors. Do not insert the screws all the way
in - leave a small gap of about 0.5 cm.
If not using screw anchors, use a screwdriver to insert the screws into the wall. Do not insert the
screws all the way in - leave a gap of about 0.5 cm.
4
Make sure the screws are fastened well enough to hold the weight of the NBG-418N with the
connection cables.
5
Align the holes on the back of the NBG-418N with the screws on the wall. Hang the NBG-418N on
the screws.
Figure 3
Wall Mounting Example
Table 2
Wall Mounting Information
Distance between holes
12 cm
M4 Screws
Two
Screw anchors (optional)
Two
Page 17 / 224
NBG-418N User’s Guide
17
C
HAPTER
2
The Web Configurator
2.1
Overview
This chapter describes how to access the NBG-418N Web Configurator and provides an overview of
its screens.
The Web Configurator is an HTML-based management interface that allows easy setup and
management of the NBG-418N via Internet browser. Use Internet Explorer 6.0 and later versions,
Mozilla Firefox 3 and later versions, or Safari 2.0 and later versions. The recommended screen
resolution is 1024 by 768 pixels.
In order to use the Web Configurator you need to allow:
•
Web browser pop-up windows from your device. Web pop-up blocking is enabled by default in
Windows XP SP (Service Pack) 2.
•
JavaScript (enabled by default).
•
Java permissions (enabled by default).
Refer to
Chapter 20 Troubleshooting
to see how to make sure these functions are allowed in
Internet Explorer.
2.2
Accessing the Web Configurator
1
Make sure your NBG-418N hardware is properly connected and prepare your computer or computer
network to connect to the NBG-418N (refer to the Quick Start Guide).
2
Launch your web browser.
3
Type "http://192.168.1.1" as the website address in your web browser. This is the default LAN IP
address in router mode, the default device mode (192.168.1.2 is the default IP address in non-
router mode).
Your computer must be in the same subnet in order to access this website address. In router mode,
the NBG-418N can assign your computer an IP address, so you must set your computer to get an IP
address automatically (computer factory default) or give it a fixed IP address in the range between
192.168.1.3 and 192.168.1.254 (see the appendices).
4
Type
admin
(default) as the user name and
1234
(default) as the password and click
OK
.
Page 18 / 224
Chapter 2 The Web Configurator
NBG-418N User’s Guide
18
Figure 4
Login Screen
Note: The management session automatically times out when the time period set in the
Administrator Inactivity Timer
field expires (default five minutes). Simply log
back into the NBG-418N if this happens.
5
Select the setup type you want to use.
• Click
Go to Wizard Setup
to use the Configuration Wizard for basic Internet and Wireless
setup.
• Click
Go to Advanced Setup
to view and configure all the NBG-418N’s settings.
•
Select a language to go to the basic Web Configurator in that language. To change to the
advanced configurator see
Chapter 19 on page 139
.
Figure 5
Selecting the setup mode
Page 19 / 224
Chapter 2 The Web Configurator
NBG-418N User’s Guide
19
2.3
Resetting the NBG-418N
If you forget your password or IP address, or you cannot access the Web Configurator, you will need
to use the
RESET
button at the back of the NBG-418N to reload the factory-default configuration
file. This means that you will lose all configurations that you had previously saved, the username
will be reset to
admin
and password will be reset to
1234
. The IP address will be reset to
“192.168.1.1”.
2.3.1
Using the RESET Button
1
Make sure the power LED is on.
2
Press the
RESET
button for longer than 1 second to restart/reboot the NBG-418N.
3
Press the
RESET
button for longer than five seconds to set the NBG-418N back to its factory-
default configurations.
Page 20 / 224
Chapter 2 The Web Configurator
NBG-418N User’s Guide
20

Rate

4 / 5 based on 1 vote.

Popular Zyxel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top