1. Home
    2. /
  2. Manuals
    3. /
  3. Zyxel
    4. /
  4. NBG334W
    5. /
  5. 24
Page 116 / 296 Scroll up to view Page 111 - 115
Chapter 8 LAN
NBG334W User’s Guide
116
The following table describes the labels in this screen.
Table 43
Network > LAN > Advanced
LABEL
DESCRIPTION
Multicast
Select
IGMP V-1
or
IGMP V-2
or
None
. IGMP (Internet Group Multicast
Protocol) is a network-layer protocol used to establish membership in a
Multicast group - it is not used to carry user data. IGMP version 2 (RFC 2236)
is an improvement over version 1 (RFC 1112) but IGMP version 1 is still in
wide use. If you would like to read more detailed information about
interoperability between IGMP version 2 and version 1, please see sections 4
and 5 of RFC 2236.
Any IP Setup
Active
Select this if you want to let computers on different subnets use the
NBG334W.
Windows Networking (NetBIOS over TCP/IP): NetBIOS (Network Basic Input/Output System) are TCP
or UDP broadcast packets that enable a computer to connect to and communicate with a LAN. For
some dial-up services such as PPPoE or PPTP, NetBIOS packets cause unwanted calls. However it
may sometimes be necessary to allow NetBIOS packets to pass through to the WAN in order to find a
computer on the WAN.
Allow between LAN
and WAN
Select this check box to forward NetBIOS packets from the LAN to the WAN
and from the WAN to the LAN. If your firewall is enabled with the default policy
set to block WAN to LAN traffic, you also need to enable the default WAN to
LAN firewall rule that forwards NetBIOS traffic.
Clear this check box to block all NetBIOS packets going from the LAN to the
WAN and from the WAN to the LAN.
Apply
Click
Apply
to save your changes back to the NBG334W.
Reset
Click
Reset
to begin configuring this screen afresh.
Page 117 / 296
NBG334W User’s Guide
117
C
HAPTER
9
Guest WLAN
Guest WLAN allows you to set up a wireless network where users can access to Internet via
the NBG334W (
Z
), but not other networks connected to the
Z
. In the following figure, a guest
user can access the Internet from the guest wireless network
A
via
Z
but not the home or
company network
N
.
You can also configure access to be Guest WLAN by using MAC filtering (see
Section 9.2 on
page 118
) and bandwidth management (see
Section 9.4 on page 120
).
"
The home or company network
N
and Guest WLAN network are independent
networks.
Figure 63
Guest Wireless LAN Network
This chapter discusses how to configure guest wireless network settings in your NBG334W.
See the appendices for more detailed information about wireless networks.
"
Pure AP mode doesn’t support Guest WLAN.
N
A
Z
Internet
Page 118 / 296
Chapter 9 Guest WLAN
NBG334W User’s Guide
118
9.1
General Guest WLAN Screen
Click
Network
>
Guest WLAN
to open the
General
screen.
Figure 64
Network > Guest WLAN > General
The following table describes the general wireless LAN labels in this screen.
9.2
Guest WLAN MAC Filter
The MAC filter screen allows you to configure the NBG334W to give exclusive access
(
Allow
) or exclude devices from accessing the NBG334W’s guest wireless network (
Deny
).
Every Ethernet device has a unique MAC (Media Access Control) address. The MAC address
is assigned at the factory and consists of six pairs of hexadecimal characters, for example,
00:A0:C5:00:00:02. You need to know the MAC address of the devices to configure this
screen.
For comparing the NBG334W’s Guest WLAN and wireless LAN, see
Appendix A on page
229
.
Table 44
Network > Guest WLAN > General
LABEL
DESCRIPTION
Enable Guest
WLAN
Select the check box to activate guest wireless LAN.
Name(SSID)
The SSID (Service Set IDentity) identifies a wireless station. Wireless stations
associating to the access point (AP) must have the same SSID. Enter a descriptive
name (up to 32 printable 7-bit ASCII characters) for the wireless LAN. Use the
default SSID (
Guest
) or enter a unique name in order to distinguish it from other
wireless networks in the same area.
Hide SSID
Select this check box to hide the SSID in the outgoing beacon frame so a station
cannot obtain the SSID through scanning using a site survey tool.
Security Mode
Select this to specify the security level for this wireless network. Select
Static WEP
,
WPA-PSK
,
WPA
,
WPA-PSK2
, or
WPA2
, the corresponding settings display below.
Or select
No Security
to not apply security setting for this wireless network. See
Section 5.5.1 on page 81
,
Section 5.5.2 on page 81
,
Section 5.5.3 on page 83
,
Section 5.5.4 on page 84
for more information.
Apply
Click
Apply
to save your changes back to the NBG334W.
Reset
Click
Reset
to reload the previous configuration for this screen.
Page 119 / 296
Chapter 9 Guest WLAN
NBG334W User’s Guide
119
To change your NBG334W’s MAC filter settings for guest wireless network, click
Network
>
Guest WLAN
>
MAC Filter
. The screen appears as shown.
Figure 65
Network > Guest WLAN > MAC Filter
The following table describes the labels in this menu.
9.3
Guest WLAN IP Screen
Click
Network
>
Guest WLAN
>
IP
. The screen appears as shown.
Table 45
Network > Guest WLAN > MAC Filter
LABEL
DESCRIPTION
Active
Select the check box to enable MAC address filtering for the Guest WLAN.
Filter Action
Define the filter action for the list of MAC addresses in the
MAC Address
table.
Select
Deny
to block access to the NBG334W, MAC addresses not listed will be
allowed to access the NBG334W
Select
Allow
to permit access to the NBG334W, MAC addresses not listed will be
denied access to the NBG334W.
Set
This is the index number of the MAC address.
MAC
Address
Enter the MAC addresses of the wireless station that are allowed or denied access to
the NBG334W in these address fields. Enter the MAC addresses in a valid MAC
address format, that is, six hexadecimal character pairs, for example,
12:34:56:78:9a:bc.
Apply
Click
Apply
to save your changes back to the NBG334W.
Reset
Click
Reset
to reload the previous configuration for this screen.
Page 120 / 296
Chapter 9 Guest WLAN
NBG334W User’s Guide
120
Figure 66
Network > Guest WLAN > IP
The following table describes the labels in this screen.
9.4
Guest WLAN Bandwidth Screen
The
Bandwidth
screen allows you to specify a priority level and restrict the maximum
bandwidth for the guest wireless network. Additionally, you can also define bandwidth for
your home or office network in the
Network
>
Wireless LAN
>
Bandwidth
. An example is
shown next to define maximum bandwidth for your networks (
A
is Guest WLAN and
N
is
home or company network.)
Figure 67
Example: Bandwidth for Different Networks
Table 46
Network > Guest WLAN > IP
LABEL
DESCRIPTION
IP Address
Type an IP address for the devices on the Guest WLAN using this as the gateway IP
address.
IP Subnet
Network
Type the subnet mask for the guest wireless LAN.
Apply
Click
Apply
to save your changes back to the NBG334W.
Reset
Click
Reset
to reload the previous configuration for this screen.
600 kbps
100 kbps
300 kbps
N
Internet
A

Rate

4 / 5 based on 1 vote.

Popular Zyxel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top