Page 161 / 236
Scroll up to view Page 156 - 160
Chapter 22 USB Media Sharing
EMG2926-Q10A User’s Guide
161
2
A screen asking for password authentication appears. Enter the user name and password (you
configured in the
USB Media Sharing > FTP
screen) and click
Log On
.
3
The screen changes and shows you the folder for the USB storage device connected to your
EMG2926-Q10A. Double-click the folder to display the contents in it.
Page 162 / 236
EMG2926-Q10A User’s Guide
162
C
HAPTER
23
Port Configuration
23.1
Overview
The EMG2926-Q10A has 1000Base-T auto-negotiating Ethernet ports. In 10/100/1000 Mbps
Gigabit Ethernet, the speed can be 10 Mbps, 100 Mbps or 1000 Mbps. The duplex mode can be both
half or full duplex. An auto-negotiating port can detect and adjust to the optimum Ethernet speed
(10/100/1000 Mbps) and duplex mode (full duplex or half duplex) of the connected device.
23.2
Port Configuration Screen
Use this screen to configure the EMG2926-Q10A port speed and duplex settings. Click
Configuration
>
Management > Port Configuration
.
Figure 103
Management > Port Configuration
The following table describes the labels on this screen.
Table 62
Management > Port Configuration
LABEL
DESCRIPTION
WAN/LAN1~4
This field displays the Ethernet port of the EMG2926-Q10A.
Speed
Select the speed of the Ethernet connection on this port. The choices are
Auto
,
1000
,
100
and
10
.
Selecting
Auto
(auto-negotiation) allows one port to negotiate with a peer port
automatically to obtain the connection speed that both ends support. If the peer port
does not support auto-negotiation or turns off this feature, the EMG2926-Q10A
determines the connection speed by detecting the signal on the cable and using half
duplex mode.
Page 163 / 236
Chapter 23 Port Configuration
EMG2926-Q10A User’s Guide
163
Duplex
Select the duplex mode of the Ethernet connection on this port. The choices are
Auto
,
Full
and
Half
.
Selecting
Auto
(auto-negotiation) allows one port to negotiate with a peer port
automatically to obtain the duplex mode that both ends support. If the peer port does
not support auto-negotiation or turns off this feature, the EMG2926-Q10A determines
the connection speed by detecting the signal on the cable and using half duplex mode.
Apply
Click
Apply
to save your changes with the EMG2926-Q10A.
Cancel
Click
Cancel
to begin configuring this screen afresh.
Table 62
Management > Port Configuration (continued)
LABEL
DESCRIPTION
Page 164 / 236
EMG2926-Q10A User’s Guide
164
C
HAPTER
24
Maintenance
24.1
Overview
This chapter provides information on the
Maintenance
screens.
24.2
What You Can Do
•
Use the
General
screen to set the timeout period of the management session (
Section 24.3 on
page 164
).
•
Use the
Account
screen to change your EMG2926-Q10A’s system password (
Section 24.4 on
page 165
).
•
Use the
Time
screen to change your EMG2926-Q10A’s time and date (
Section 24.5 on page
166
).
•
Use the
Firmware Upgrade
screen to upload firmware to your EMG2926-Q10A (
Section 24.6 on
page 168
).
•
Use the
Backup/Restore
screen to view information related to factory defaults, backup
configuration, and restoring configuration (
Section 24.8 on page 171
).
•
Use the
Restart
screen to reboot the EMG2926-Q10A without turning the power off (
Section
24.8 on page 171
).
•
Use the
Sys OP Mode
screen to select how you want to use your EMG2926-Q10A (
Section 24.10
on page 172
).
•
Use the
Language
screen to change the language for the Web Configurator (
Section 24.11 on
page 173
).
•
Use the
Diagnostic > Ping
screen to ping an IP address (
Section 24.12 on page 173
).
24.3
General Screen
Use this screen to set the management session timeout period. Click
Maintenance
>
General
.
The following screen displays.
Page 165 / 236
Chapter 24 Maintenance
EMG2926-Q10A User’s Guide
165
Figure 104
Maintenance > General
The following table describes the labels in this screen.
24.4
Account Screen
It is strongly recommended that you change your EMG2926-Q10A's password.
If you forget your EMG2926-Q10A's password (or IP address), you will need to reset the device.
See
Section 24.8 on page 171
for details.
Click
Maintenance
>
Account
. The screen appears as shown.
Figure 105
Maintenance > Account
The following table describes the labels in this screen.
Table 63
Maintenance > General
LABEL
DESCRIPTION
System Name
System Name is a unique name to identify the EMG2926-Q10A in an Ethernet network.
Domain Name
Enter the domain name you want to give to the EMG2926-Q10A.
Administrator
Inactivity Timer
Type how many minutes a management session can be left idle before the session times
out. The default is 5 minutes. After it times out you have to log in with your password again.
Very long idle timeouts may have security risks. A value of "0" means a management
session never times out, no matter how long it has been left idle (not recommended).
Apply
Click
Apply
to save your changes back to the EMG2926-Q10A.
Cancel
Click
Cancel
to exit this screen without saving.
Table 64
Maintenance > Account
LABEL
DESCRIPTION
User Account Entries
#
This is the index number of a user account.
User Name
The EMG2926-Q10A’s user account name.
19216811.live