1. Home
    2. /
  2. Manuals
    3. /
  3. ZTE
    4. /
  4. ZXV10-W300v5
    5. /
  5. 8
Page 36 / 89 Scroll up to view Page 31 - 35
Chapter 2 - Product Installation
Parameter
Description
IP Subnet Mask
Enter the W300 IP subnet mask. By default, it is 255.255.255.0.
Dynamic Route
Select the Routing Information Protocol (RIP) to be used from the
dropdown list. And select the direction from the dropdown list
Multicast
Select the multicast protocol to be used from the dropdown list
DHCP
DHCP function can be disabled, enabled or in relay mode. Figure 13 shows
the parameters when DHCP is enabled. And Table 13 gives the parameter
descriptions.
T
A B L E
13 T
H E
D
E S C R I P TI O N S
O F
T H E
DHCP P
A R A M E T E R S
Parameter
Description
Starting
IP
Address
Enter the starting IP address to be used by the DHCP server’s IP
assignment. By default, the starting IP address is 192.168.1.2
and the ending IP address is 192.168.1.254.
IP Pool Count
Enter the maximum user pool size to be assigned.
Lease Time
Enter the amount of time to lease out a given IP address.
DNS Relay
Select the DNS relay option to be used from the dropdown list. If
the users do not want to use the DNS relay option, set the DNS
relay to “Use User Discovered DNS Server Only” and set both
Primary and Secondary DNS servers to 0.0.0.0.
Primary
DNS
Server
Enter the primary DNS server IP address to be used. For user
discovered DNS only.
Secondary DNS
Server
Enter the secondary DNS server IP address to be used. For user
discovered DNS only.
A DHCP relay is a computer that forwards DHCP data between computers
that request IP address and the DHCP server that assigns the IP address. If
the DHCP Relay option is enabled, DHCP requests from local PCs will be
forwarded to the DHCP server that runs on WAN side. For this function
working properly, W300 must run on the router mode, disable the DHCP
server on the LAN port and make sure the routing table has the correct
routing entry.
Proprietary Information of ZTE CORPORATION
25
Page 37 / 89
ZXV10 W300 (V5.2) Wireless ADSL Router Maintenance Manual
If relay DHCP is selected, Figure 14 will be display on the web configuration
page. Table 14 describes the parameter.
F
I G U R E
14 T
H E
R
E L A Y
DHCP W
E B
C
O N F I G U R A T I O N
P
A GE
T
A B L E
14 T
H E
R
E L A Y
DHCP P
A R A M E T E R
Parameter
Description
DHCP Server IP
for Relay Agent
Enter the IP address for the DHCP relay agent.
Wireless Configuration
Click
Interface Setup>Wireless
to show the
Wireless
configuration page,
as shown in Figure 15.
26
Proprietary Information of ZTE CORPORATION
Page 38 / 89
Chapter 2 - Product Installation
F
I G U R E
15 T
H E
W
I R E L ES S
C
O N F I G U R A T I O N
P
A GE
Access Point Settings
Table 15 describes the access point setting parameters.
Proprietary Information of ZTE CORPORATION
27
Page 39 / 89
ZXV10 W300 (V5.2) Wireless ADSL Router Maintenance Manual
T
A B L E
15 T
H E
A
C C E S S
P
O I N T
P
A R A M E T E R S
Parameter
Description
Access Point
By default, it is activated. If there is no wireless device in the
network, select
Deactivated
.
Channel
Select a channel from the dropdown list.
Beacon Interval
A beacon is a packet broadcasted by the router to synchronize
the wireless network. Enter a value between 20 and 1000.
RTS/CTS
Threshold
The RTS (Request To Send) threshold for enabling RTS/CTS
handshake. Enter a value between 1500 and 2347.
Fragmentation
Threshold
The maximum fragment size that can be sent. Enter a value
between 256 and 2346.
DTIM
Enter a value between 1 and 255. It indicates the interval of eh
Delivery Traffic Indication Message (DTIM).
802.11 b/g/n
The default setting is 802.11 b+g+n. other modes can be
selected from the dropdown list.
Station Number
Enter a value between 0 and 16
Multiple SSIDs Settings
The SSID is the name of a wireless access point to be distinguished from
another. It is case sensitive and must not exceed 32 characters. User can set
multiple SSIDs for W300. Table 16 describes the parameters.
T
A B L E
16 T
H E
M
U L T I P L E
SSID
S
P
A R A M E T E R S
Parameter
Description
SSID Index
Select an index number from the dropdown list.
SSID
Enter the SSID name.
Broadcast SSID
Select
No
to hide the SSID in so that a station cannot obtain the
SSID through passive scanning; select
Yes
to make the SSID
visible so that a station can obtain the SSID through passive
scanning.
Authentication
Type
Select the authentication type from the dropdown list.
28
Proprietary Information of ZTE CORPORATION
Page 40 / 89
Chapter 2 - Product Installation
Wireless MAC Address Filter
The MAC filter function allows the user to configure the W300 to give access
or deny access to specified devices. Every Ethernet device has a unique MAC
(Media Access Control) address. The MAC address is assigned at the factory
and consists of six pairs of hexadecimal characters, for example,
00:AA:BB:00:00:02.
Table 17 describes the parameters.
T
A B L E
17 T
H E
MAC F
I L TE R
P
A R A M E T E R S
Parameter
Description
Active
Select
Activated
to enable MAC address filtering.
Action
Select
Deny Association
to block access to W300 or select
Allow Association t
o permit access to W300
MAC Address
#1 ~ #8
Enter the MAC address of the devices that are allowed or denied
access to the router in these address fields.
Click the
SAVE
button to save the changes, for configurations mentioned in
this chapter.
Proprietary Information of ZTE CORPORATION
29

Rate

4.5 / 5 based on 2 votes.

Popular ZTE Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top