ZTE H220N Router Manual PDF (Setup & Configuration Guide)

Page 11 / 16 Scroll up to view Page 6 - 10

4.2.2

WLAN

WLAN Configuration

Configuration

1.

Select [

Network→WLAN→Basic 11n

] to open the

WLAN Basic Parameter

page, as

shown in the ﬁgure below.

2.

Set the parameters according to the description below.

Parameter Name

Description

Enable Wireless RF

Enable/disable WLAN RF.

Enable Isolation

Enable/disable internal isolation.

Mode

Wireless communication mode, including

Mixed (802.11b+802.11g) and Mixed

802.11b+802.11g+802.11n.

Country/Region

Country or region where the device to be used.

Band Width

Band width to be set. Options: 20MHz and 40MHz.

The value is 20MHz by default. Configurable when

Mixed (802.11b+802.11g+802.11n) is enabled only.

Channel

Wireless signal channel. Select from auto and integ

ers from 1 to 13 according to the country code. The

default value is Auto.

Wireless channel used in the communication between

the wireless access point and wireless station, which

channel to use depends on the local administration.

All stations communicating with H108L must use the

same channel.

SGI Enable

Enable/disable SGI. Configurable when 802.11n

mode is enabled only.

Beacon Interval

The default value is 100ms.

1

0

Page 12 / 16

Parameter Name

Description

Transmitting Power

Transmitting power level. Options: 100%, 80%, 60%,

40% and 20%. The default value is 100%.

Transmitting Power indicates the ration of the output

power to the maximum power. The higher the power

is, the longer the transmitting distance is.

QoS Type

The default value is WMM.

3.

Click

Submit

button to complete WLAN conﬁguration.

4.2.3

WLAN

WLAN Security

Security

Security Configuration

Configuration

1.

Select [

Network→WLAN→Security

] to open the

WLAN Security Conﬁguration

page.

2.

Conﬁgure parameters on the basis of the following description.

Parameter Name

Description

Choose SSID

The default value is SSID1.

Authentication Type

Options: Open System (indicating no encryption),

shared key, WPA-PSK, WPA2-PSK and

WPA/WPA2-PSK.

WPA Passphrase

WPA encryption key, which contains 8 to 63

characters.

WPA Group Key Update

Interval

The interval of WPA group key update. The default

value is 600 seconds.

WPA Encryption Algorithm

WPA entryption algorithm, which supports TKIP, AES

and TKIP+AES.

If users want to enable TKIP or TKIP+AES encryption

algorithm, please firstly enable

Mixed (802.11b+802.

11g)

wireless communication mode.

Available encryption methods include WPA encryption, WEP encryption, and no encryption.

1

Page 13 / 16

l

WPA encryption

Wi-Fi

Protected

Access

(WPA)

includes

WPA-PSK,

WPA2–PSK,

and

WPA/WPA2–PSK.

a.

Select

WPA-PSK

,

WPA2–PSK

or

WPA/WPA2–PSK

from the drop-down list of

Au-

thentication Type

option to enable WPA encryption.

b.

Set the parameters according to the description above.

l

WEP encryption

Wired Equivalent Privacy (WEP) is a widely used WLAN security protocol.

a.

Select

Shared Key

from the drop-down list of

Authentication Type

option to open

the page as shown in the following ﬁgure.

b.

Set the parameters according to the description below.

Parameter Name

Description

WEP Encryption

Enable/disable WEP encryption. The encryption

is disabled by default.

WEP Encryption Level

The length of WEP encryption key is 64bit or

128bit.

WEP Key Index

Index of WEP encryption key.

WEP Key1–WEP Key4

WEP encryption keys. 64 bit WEP encryption

key corresponds to 5 ASCII characters or

10 hexadecimal characters. 128bit WEP

encryption key corresponds to 13 ASCII

characters or 26 hexadecimal characters.

3.

Click

Submit

button to complete WLAN security conﬁguration.

1

2

Page 14 / 16

5

Troubleshooting

You may encounter some problems when installing or using H108L. Please try the following

solutions. If the problem still exists, please contact the service provider for help.

Problem

Solution

The power indicator is off

after the device is switched

on

Use standard power adapter, such as the power adapter

delivered with the device. Make sure that the adapter is

connected properly to both H108L and the power socket.

The LAN indicator is off after

Ethernet cable is connected

Make sure that the Ethernet, PC, and H108L are correctly

connected, and that the PC and H108L are switched on.

The DSL indicator is off after

telephone line is connected.

Make sure that the telephone line in use is standard line

(delivered with the device) and all devices are correctly

connected according to the previous description. Check

whether the cables are properly plugged in. Please allow 60

seconds for H108L to establish connection to the operator.

The DSL indicator flashes

slowly after telephone line is

connected

Indicates that H108L failed to get connected with the

DSLAM system of the operator. Please make sure that

H108L is correctly connected according to the previous

solutions. If a telephone is installed before the splitter,

please make sure that the splitter is correctly installed.

WLAN cannot be connected

l

Make sure that the WLAN RF is switched on, and the

WLAN indicator is on.

l

Check whether the wireless network card is correctly

configured.

l

Check whether the network name, encryption mode,

and encryption key stored in the PC are consistent with

the settings of H108L.

PC is unable to access the

network

l

Check whether the IP address of H108L(192.168.1.1 by

default) can be pinged successfully from the PC. If cann

ot, please check the Ethernet connection and whether

the indicator status is normal.

l

It is recommended to set the IP address and DNS server

address to be obtained automatically.

l

It is recommended to disable all running firewall or secu

rity software.

l

Disable the proxy server of the Web browser.

l

Check whether the indicator status is normal.

1

3

Page 15 / 16

6

Specification

Physical Specification

l

Size

Excluding bracket: 200mm * 168mm * 36mm (length * width * height)

Including bracket: 200mm * 168mm * 75mm (length * width * height)

l

Weight

Excluding bracket: 300g (excluding power adapter)

Including bracket: 360g (excluding power adapter)

Electric Specification

l

Non-USB Scenario

Power supply: Input 220V AC/50Hz, output 12V AC/750mA

Power: 9W

l

USB Scenario

Power supply: Input 220V AC/50Hz, output 12V AC/1A

Power: 12W

Environmental Requirements

Temperature: 0

℃

-

45

℃

, humidity: 5%

-

95%.

Qualifications

CCC, Network Access License, Wi-Fi, Radio Transmitter Model Authorization.

ZTE CORPORATION reserves the right to upgrade or make technical change to this product

without further notice.

1

4

Rate

Popular ZTE Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share