ZTE H220N Router Manual PDF (Setup & Configuration Guide)

Page 6 / 16 Scroll up to view Page 1 - 5

Name

Function

Description

LAN1–LAN4

Ethernet

ports

Connects to PC’s network adapter or other network

device via RJ-45 cable.

DSL

DSL socket

Connects to ADSL cable or splitter via RJ-11

telephone line.

l

Sockets and buttons on the side panel of H108L

Socket and buttons on the side panel of H108L are as follows:

The description of sockets and buttons on the side panel of H108L is as follows:

Name

Function

Description

On/Off

Power switch

Switches on or off power supply.

WLAN

WLAN RF switch

keep pressing the button for more than 5 seconds

to switche on or off WLAN RF.

WPS

WPS access

switch

Switches on or off WPS access.

USB1/USB2

USB port

Connects USB storage devices.

Notes:

The quantity of USB ports ranges from 0 to 2 depending on the actual product

model.

3

Installation

3.1

Installing

Installing Device

Device

Appropriate space for heat dissipation is required to prevent the device from overheating. Do

not place the device close to heat sources or under direct sunlight. Do not block the heat dis-

sipation opening.

1.

Placement: Place the device at a place where its surface is plane and where there will be

less obstacles when communicating with the wireless terminals to ensure the best signal

strength. It is recommended to use wireless terminals in the room where H108L is placed

or the immediate room.

2.

H108L adopts the ADSL uplink mode to get connected to the Internet. It is recommended

to connect the device as the approach shown in the following ﬁgure.

5

Page 7 / 16

3.

If a telephone is required to be installed before the splitter, make sure to connect a voice

ﬁlter properly to the

Line

socket of the splitter, and then connect the telephone to the ﬁlter.

Connect other sockets as the above ﬁgure.

Notes:

Please use the power adapter delivered with the device.

Otherwise the device

might be damaged.

3.2

Setting

Setting Preparations

Preparations

3.2.1

Checking

Checking PC

PC

PC Settings

Settings

It is recommended to turn off VPN and ﬁrewalls on your PC.

The following uses Microsoft IE as an example to introduce the steps to disable IE proxy service.

1.

Select [

Tools→Internet Options

] in the browser. Then the

Internet Options

window pops

up.

2.

In the

Internet Options

window, select

Connections

tab and click

LAN Settings

.

3.

Uncheck

Use a proxy server for your LAN

in the pop-up window. Then click

OK

to submit.

3.2.2

Configuring

Configuring TCP/IP

TCP/IP

The following uses Windows XP as an example to introduce the steps to conﬁgure TCP/IP.

1.

In the Windows taskbar, select [

Start→Control Panel

].

2.

In the

Control Panel

window, double-click

Network Connection

.

3.

In the

Network Connection

window, right-click

Local Area Connection

. In the pop-up

menu, click

Properties

. Then the

LAN Properties

dialog box pops up.

4.

Select

Internet Protocol (TCP/IP)

and click

Properties

.

Then the

Internet Protocol

(TCP/IP) Properties

dialog box pops up.

5.

There are two approaches to conﬁgure TCP/IP. However, the ﬁrst approach is recom-

mended.

6

Page 8 / 16

l

First approach: Acquire an IP address automatically from H108L via DHCP.

a.

In the

Internet Protocol (TCP/IP) Properties

dialog box, check

Obtain an IP ad-

dress automantically

and

Obtain DNS server address automatically

.

b.

Click

OK

to save conﬁguration.

l

Second approach: Specify a static IP address for PC.

a.

In the

Internet Protocol (TCP/IP) Properties

dialog box, check

Use the following

IP address

to set the IP addresses of PC and H108L to the same network segment,

in the form of 192.168.1.x (x is an integer between 2 to 254).

For example, IP is set to

192.168.1.2

, subnet mask is set to

255.255.255.0

, and

both default gateway and DNS server are set to

192.168.1.1

.

b.

Click

OK

to save conﬁguration.

3.3

Configuring

Configuring Wireless

Wireless

Wireless Connection

Connection

1.

The PC is able to connect to WLAN network when it is equiped with wireless network card.

2.

Before the PC is able to get connected with a WLAN network, the installation and conﬁgu-

ration of wireless network card must be completed.

3.

The wireless network card will search for wireless networks automatically after installation

and conﬁguration is completed.

The PC will be ready for use after search succeed.

If

encryption is enabled on H108L, users will be prompted for corresponding encryption key.

3.4

Restoring

Restoring Default

Default

Default Settings

Settings

If the device fails to function or users forget their login password due to incorrect conﬁgurations,

the problem can be resolved by restoring default settings.

Refer to

the label on

the bottom of device for detailed default

setting parameters.

1.

When the device is operating normally, keep pressing the

Reset

button for more than 5

seconds (using a needle or a pin).

2.

The system will restore default settings and restart automatically.

4

WEB

WEB Configuration

Configuration

4.1

Login/Logout

H108L provides Web-based conﬁguration, which enables users to conﬁgure and manage

H108L via Web browser.

1.

Type

http://192.168.1.1

(the default IP address of the LAN-side interface of H108L) in the

address bar of IE browser and press

Enter

. Then the

Login

page shown in the following

ﬁgure pops up.

7

Page 9 / 16

2.

Input username and password (default username and password are

admin

and

admin

) and

click

Login

to enter H108L page.

3.

Click

Logout

at the top-right corner of corresponding page to exit.

4.2

Network

Network Configuration

Configuration

4.2.1

Creating

Creating WAN

WAN

WAN Connection

Connection

1.

Select [

Network→WAN→WAN Connection

] to open the

WAN Connection

page as

shown in the ﬁgure below.

2.

Set the parameters according to the description below.

Parameter Name

Description

Connection Name

The default value is

Create WAN Connection

. Users

can select created network connections from the

drop-down menu.

Type

Type of connection. Select WAN connection type from

five options including PPPoE, PPPoA, Static (need the

operator to provide IP address), DHCP and Bridge

Connection. The default value is PPPoE.

New Connection Name

Contains 1 to 256 characters.

8

Page 10 / 16

Parameter Name

Description

Enable NAT

Enable/disable Network Address Translation (NAT). This

function can be configured in route mode only. It cannot

be configured in bridge mode.

Enable VLAN

Enable/disable VLAN configuration. VLAN ID and 802.1p

are used to define to which VLAN the device belongs

as well as the priority.

VLAN ID

VLAN ID of data packets at WAN interface. The value

ranges from 1 to 4094.

802.1p

Deals with priority, suitable for multiple WAN connections

only. The value ranges from 0 to 7. The default value is

0, which indicates no priority set. The greater the value

is, the higher the priority is.

VPI/VCI

VPI/VCI (Virtual Path/Channel Identifier) identifies virtual

path and virtual channel of a link.

In the case of first-time configuration, select

Create

, and

then configure the VPI/VCI values.

Otherwise, select a

previously used VPI/VCI values from the drop-down list.

New VPI/VCI

Configures VPI/VCI values, which range from 0 to 255

and from 0 to 65535 respectively. Both of which are

provided by the ISP.

Encapsulation Type

The protocol encryption type, which supports LLC and

VCMUX.

Service Type

Configuration of ATM QoS which imposes restrictions on

uplink traffic. Four types are available: CBR, RT-VBR,

nRT-VBR and UBR.

Username/Password

Username and password for WAN connection

authentication. Both of which are provided by the ISP.

Authentication Type

Authentication protocol type. Options: Auto, PAP and

CHAP. The value is Auto by default.

Connection Trigger

Connection triggering mode. Options: Always On, On

Demand, and manual. The mode is Always on by default.

Idle Timeout

The default value is 1200 seconds. It can be set when

the

Connection Trigger

is set to

On Demand

only.

3.

Click

Create

to create connection.

9

Rate

Popular ZTE Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share