Page 31 / 58
Scroll up to view Page 26 - 30
zNID 24xx series LEDs
zNID Hardware Installation Guide
31
GE
Figure 8:
zNID-GE-24xx LEDS
Table 4:
zNID-GE-24xx LEDs
LED Name
Color
Indicates
STATUS
Green: Heartbeat
(1 short blink every
5 seconds)
Normal Operation
Green: Rapid blink
(10/sec)
Unit has been reset to Factory
Defaults / is unconfigured
Green: Alternating
fast blinking and
Off (1 second rapid
blink/1 second off)
EZ Touch communications in process
Green: Slow blink
(1/second)
Remote Mgt Access (OMCI, SNMP,
HTTP, Telnet, or TR-069)
Green: On
Reboot or restart in process
Off
Power off
BATT
Yellow: On
Operating on Battery Power
Yellow: Slow blink
(1/sec)
Battery Alarm (Low Battery, Missing,
or Replace)
Off
Normal operation on AC power
ALARM
Red: On
Running on battery
Red: 50% cycle:
1
sec Rapid Blink/
1 sec Off
EZ Touch actions pending -- SW or
Config update required
Off
Normal operation on AC power
WAN
Green: On
Ranged successfully
Green: Slow blink
(1/sec)
Ranging in progress
Off
Not ready for ranging or not
provisioned
Page 32 / 58
zNID 24xx Series
32
zNID Hardware Installation Guide
CONFIG
Green: On
OMCI provisioning is complete
Green: Rapid blink
(10/sec)
OMCI provisioning is written to
FLASH
Green: Slow blink
(1/sec)
OMCI provisioning is in progress
Off
No OMCI provisioning
GE1 – GE4
Green: On
Ethernet interface link
Green: Flash
Data transmitting
Off
No link on Ethernet interface
VOICE
Green: On
Registered successfully
Green: Slow blink
(1/sec)
Off hook
Off
Registration failed or telephone
service is not provisioned
USB
Green: On
Connected
Off
No power/USB not connected
WIFI
Green: On
WIFI enabled
Green: Flash
Data transmitting
Off
WIFI disabled
WPS
Green: Long flash
Success
Green: Flash
In progress
Off
WPS disabled
VIDEO
Green: On
1550nm signal is normal and RF
video output is enabled
Green: Slow blink
(1/sec)
RF video output is enabled, but no
1550nm signal received
Off
RF video output is disabled
Table 4:
zNID-GE-24xx LEDs
LED Name
Color
Indicates
Page 33 / 58
Logging in to the 24xx series zNID
zNID Hardware Installation Guide
33
Logging in to the 24xx series zNID
The zNID 24xx series may be managed from OMCI, Web UI or CLI. This
section describes logging into the zNID locally using the subscriber facing
LAN port, GE1.
Figure 9:
Log into GE port 1 to reach the Web UI or CLI on the zNID
To login with a browser:
1
Connect an Ethernet cable from your computer to GE1 on the zNID.
2
3
Enter the username and password.
The default username/password is admin/zhone.
To login with a telnet session:
1
Connect an Ethernet cable from your computer to GE1 on the zNID
2
3
Enter the username and password.
The default username/password is admin/zhone.
Page 34 / 58
zNID 24xx Series
34
zNID Hardware Installation Guide
Page 35 / 58
zNID Hardware Installation Guide
35
Z
NID 24
XX
I
NSTALLATION
This chapter can be used as separate installation instructions. This chapter
explains how to unpack the zNID 24xx and install the zNID 24xx hardware. It
includes the following sections:
•
Install the zNID, page 35
•
Overview of zNID 24xx series installation, page 36
Install the zNID
This section describes the procedures for installing the zNID. The overiew
procedure provides options for wall mounting or placing the zNID on a
surface with or without the optional fiber tray.
This section contains the following topics:
•
Overview of zNID 24xx series installation
on page 36
•
Installation precautions
on page 37
•
Mount the zNID
on page 38
–
Wall mount with fiber tray
on page 38
–
Wall mount without fiber tray
on page 41
–
Desktop with fiber tray
on page 43
•
Manage the optical cable
on page 44
•
Fiber handling
on page 44
•
Testing optical power
on page 44
•
Optical fiber cable placement in the zNID fiber tray
on page 45
•
Connect to network
on page 46
•
Connect power
on page 48
•
Connecting phone terminals
on page 49
•
Connecting Ethernet ports
on page 50
•
Complete the zNID installation
on page 52
19216811.live