Zhone 1518-A1-xxx Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Zhone

1518-A1-xxx

Page 41 / 117 Scroll up to view Page 36 - 40

15xx-A1 Family Router Users Guide

Other types of NAT have restrictions such as the sending IP address must initially have

had packets sent from the private IP address and port regardless of the external port, or

from the private IP address and the external port.

Enable NAT

must be checked for Fullcone NAT to be used.



Dial on demand

: When this mode is selected, the connection that has no traffic within

assigned disconnect timeout (e.g. 1 minute) will be automatically disconnected. The

connection will be activated again when traffic arrives. This function is advantageous for

users who are charged with online time. It should be noticed that some programs

automatically link to Internet. Computer will send data to network when infected by virus.

Connection will not be disconnected under these data streams.



Inactivity Timeout

: When

“

Dial on demand

”

is selected, this input box indicates that

after how long the connection will be disconnected in the absence of traffic. If the value is

0, connection will not be disconnected.



Enable manual MTU set

: the Maximum transmission unit (MTU) value may be set for

your needs. Higher MTU can provide for a more efficient link because each packet will

carry more data while the overhead in the packet such as header information does not

get larger with the size of the packet. So the bulk throughput on the link will go up.

Generally a large packet size can occupy the time on the link, so the higher MTU can

increase lag time and minimum latency which is not appropriate for all applications.



Manual Connect

: connect/disconnect PPPoE connection manually



Enable NAT

: To define NAT services in the

Advanced Setup | NAT

screens, NAT must

be enabled.



Enable Firewall

: Enables Firewall.



Use Static IPv4 Address

: Defines a static IP address (v4) which you enter in the

IPv4

Address

text box which is displayed when the

Use Static IPv4 Address

check box is

selected.



Enable PPP Debug Mode

: Used to debug PPPoE issues. Use only when instructed by

your ISP.



Enable KeepAlive

: Enables/disables TCP keep alive packets



Enable IGMP Multicast Proxy

: Configures the router for IGMP snooping so the router

can keep limit multicast traffic.

On the

Routing

—

Default Gateway

page set the priority of WAN interfaces used as default

gateways then click

If multiple WAN interfaces are configured, you can define the priority by their position in the

Selected Default Gateway Interfaces

window. Top is the highest priority; bottom the

lowest.

Change the priority order by removing all items from the

Selected Default Gateway

Interfaces

window by selecting them, then clicking the right arrow button. Select the items in

the priority order, then click the left arrow to move them into the

Selected Default Gateway

Interfaces

window.

On the

DNS Server Configuration

page set the priority of WAN interfaces to be used as

DNS server interfaces then click

If multiple WAN interfaces are configured, you can define the priority by their position in the

Selected DNS Server Interfaces

window. Top is the highest priority; bottom the lowest.

Change the priority order by removing all items from the

Selected DNS Server Interfaces

window by selecting them, then clicking the right arrow button. Select the items in the priority

order, then click the left arrow to move them into the

Selected DNS Server Interfaces

window.

For a

Static DNS IP Address

, enter a primary and secondary DNS server for your modem,

Page 42 / 117

15xx-A1 Family Router Users Guide

On the

WAN Setup

–

Summary

page review your settings and click

Apply/Save

to accept

the settings. To change your settings, click the

Back

button on the

WAN Setup

–

Summary

page (do not click the browser Back button).

In the

Wide Area Network (WAN) Service Setup

page, you will see the new WAN interface

added.

Add an IPoA WAN Service

Add a PPPoA Layer 2 interface as described above (Add a Layer 2 Interface).

Under Advanced Setup click WAN Service then click Add

WAN Service Interface Configuration

page, select the DSL link associated with the IPoA

interface

from the drop down, then click

On the

WAN Service Configuration

page, enter a name if you wish to customize the

description shown for the service, then click

On the

WAN IP Settings

page enter a WAN IP address and WAN subnet mask as

instructed by your ISP, then click

On the

Network Address Translation Settings

you will need to enter information provided

by your ISP, then click

Next.



Enable NAT

must be checked for Fullcone NAT to be used.



Enable Fullcone NAT

: RFC 3489 defines four types of Network Address Translation

(NAT). Fullcone NAT. As with other types of NAT there is a mapping from a public IP

address to a private IP address. The external public IP address is extended with the

external port. With Fullcone NAT once the mapping is created any external host may

send packets to the private IP address by sending to the external IP address and port.

Other types of NAT have restrictions such as the sending IP address must initially have

had packets sent from the private IP address and port regardless of the external port, or

from the private IP address and the external port.



Enable Firewall

: Enables Firewall.



Enable IGMP Multicast

: Configures the router for IGMP snooping so the router can keep

limit multicast traffic.

On the

Routing

—

Default Gateway

page set the priority of WAN interfaces used as default

gateways then click

If multiple WAN interfaces are configured, you can define the priority by their position in the

Selected Default Gateway Interfaces

window. Top is the highest priority; bottom the

lowest.

Change the priority order by removing all items from the

Selected Default Gateway

Interfaces

window by selecting them, then clicking the right arrow button. Select the items in

the priority order, then click the left arrow to move them into the

Selected Default Gateway

Interfaces

window.

On the

DNS Server Configuration

page set the priority of WAN interfaces to be used as

DNS server interfaces then click

If multiple WAN interfaces are configured, you can define the priority by their position in the

Selected DNS Server Interfaces

window. Top is the highest priority; bottom the lowest.

Page 43 / 117

15xx-A1 Family Router Users Guide

Change the priority order by removing all items from the

Selected DNS Server Interfaces

window by selecting them, then clicking the right arrow button. Select the items in the priority

order, then click the left arrow to move them into the

Selected DNS Server Interfaces

window.

For a

Static DNS IP Address

, enter a primary and secondary DNS server for your modem,

10.

On the

WAN Setup

–

Summary

page review your settings and click

Apply/Save

to accept

the settings. To change your settings, click the

Back

button on the

WAN Setup

–

Summary

page (do not click the browser Back button).

In the

Wide Area Network (WAN) Service Setup

page, you will see the new WAN interface

added.

WAN Setup

—

Summary

When the settings are complete, the next screen shows a

WAN Setup

–

Summary

screen

displaying the WAN configurations made.

Make sure that the settings on the

WAN Setup - Summary

screen match the settings

provided by your ISP. If all settings are correct, click the

Apply/Save

button to save these

settings; if not, click

Back

to make any modifications (do not click the browser Back button)..

If you want to change any item after saving, click

Edit

to make any modifications.

Click

Apply/Save

to save the settings.

Page 44 / 117

15xx-A1 Family Router Users Guide

After the settings are saved, the below screen will follow displaying the WAN settings that

you made with the option to

Add

Remove

any of the connections that you have made.

Remove a Connection

If you want to delete a connection from the listed WAN setup, click the

Remove

check box next to

the connection, then click

Remove

Edit a Connection

If you want to modify a connection from the listed WAN setup, click the

Edit

button next to the

connection.

NOTE:

Some connection settings cannot be edited after they have been created. You will need to

delete and re-add the connection to change some settings.

Ethernet Mode

Ethernet mode allows you to select the speed of your Ethernet connection.

Modes include

—

auto,

100 full, 100 half, 10 full and 10 half.

If you select

auto

then the router will use the common

mode that all the connected interfaces can operate at.

Page 45 / 117

15xx-A1 Family Router Users Guide

LAN Local Area Network (LAN) Setup

You can configure the DSL Router IP address and Subnet Mask for the LAN interface to

correspond to your LAN‘s IP Subnet.

.Changing the IP address here may cause your browser to

be disconnected from the modem.

You will need to set your PC to the same subnet as the

modem

‘s

IP address to access the router again.

IGMP snooping

If you want the DHCP server to automatically assign IP addresses, then enable the DHCP server

and enter the range of IP addresses that the DHCP server can assign to your computers. Disable

the DHCP server if you would like to manually assign IP addresses.

Default

–the default LAN configuration is based on your router‘s IP address.

Static IP Lease

list

–

you can configure the DHCP server to set aside up to 32 static IP

addresses based on the MAC addresses of the device connected to the router by clicking on the

add entries button.

To remove the Static IP address, click the check box next to the MAC address and click

Remove

Entries

You may be able to assign a second IP address for the modem.

To do that, click the check box

Configure the second IP Address

and enter the IP address and subnet mask.

Click the

Apply/Save

button to save the LAN configuration data.

Rate

Popular Zhone Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share