Page 76 / 210
Scroll up to view Page 71 - 75
030-300554 Rev. A
76
June 2008
Verizon FiOS Router (Model 9100EM)
User Guide
12.2.2.1
Configure Connection—Broadband Connection Ethernet
In the
Broadband Connection (Ethernet) Properties
screen, select
Configure Connection
in the left submenu.
The following screen appears. Next, click the
Quick Setup
button.
The following screen appears. Select
Ethernet
from the
WAN Interface
drop-down list. Selecting
Ethernet
means
that the WAN Ethernet port on the rear of the Router will be Enabled, ready for connection to another device through
which you will connect to the Internet. Click
Apply
to save the settings.
NOTE:
Verizon provides the protocol mode for your connection to the Internet. Depending on your connection
type, a login user name and password may be required. These values are provided by Verizon.
Page 77 / 210
030-300554 Rev. A
77
June 2008
Verizon FiOS Router (Model 9100EM)
User Guide
12.2.2.2
QoS—Broadband Connection Ethernet
NOTE: This section is only intended to be modified by a Verizon technician.
Any changes to this section may
result in a disruption of service.
If you select
QoS
in the left submenu of the
Broadband Connection (Ethernet) Properties
screen, the following
screen appears.
You may use this section to remove VLAN tags to your incoming (Ingress) packets, or allow specific tagged packets
to enter.
To add a new entry, click the
New Entry
link. The following screen appears. Enter the desired port in the
VLAN ID
in the field, and then select an Egress Policy from the drop-down list. Click
OK
.
Page 78 / 210
030-300554 Rev. A
78
June 2008
Verizon FiOS Router (Model 9100EM)
User Guide
The following screen appears. The VLAN ID displays the port that you added and the policy assigned to the port.
Click
Apply
to save the settings.
For outgoing (Egress) packets you may enable a
Rate Limit
by checking the rate limit check box, and you may also
enable the pass through of standard QoS classifiers.
These are 802.1p, DSCP, and port tags.
N
ote that any
changes to your egress setting will likely result in a disruption of your FiOS service.
12.2.2.3
Advanced—Broadband Connection Ethernet
If you select
Advanced
in the left submenu of the
Broadband Connection (Ethernet) Properties
screen, the
following screen appears.
To add a new IP address, click the
New IP Address
link.
Page 79 / 210
030-300554 Rev. A
79
June 2008
Verizon FiOS Router (Model 9100EM)
User Guide
The following screen appear. Enter the desired IP Address and Subnet Mask in the fields provided. Then, click
Apply
to allow the settings to take effect.
The entry will be added to the list of broadband connection IP addresses.
Page 80 / 210
030-300554 Rev. A
80
June 2008
Verizon FiOS Router (Model 9100EM)
User Guide
12.2.3
Broadband Connection (Coax)
To access the Router’s broadband configurations (Coax), click
My Network
in the main menu. Then click
Network
Connections
in the left submenu. The following screen appears. Broadband Connection describes the hardware used
to connect the Router to the Internet. This screen displays Ethernet and Coax as broadband connection options. In
this setup, Coax is Connected, and Ethernet is Disabled. This means that Coax is the hardware used to connect the
Router to the Internet.
To view the Router’s broadband connection properties, in the preceding
Network Connections
screen, click the
Broadband Connection (Coax)
link. The following screen appears. If you change the name, click
Apply
to save
the change.
19216811.live