Page 41 / 114
Scroll up to view Page 36 - 40
Ubee Interactive
Using the LAN IPv6 Option
Ubee DVW32CB Advanced Wireless Voice Gateway Subscriber User Guide
•
January 2015
37
5.4
Using the LAN IPv6 Option
Use the
LAN IPv6
option to connect clients with LAN IPv6 addresses.
Steps
To configure LAN IPv6 settings:
1.
Click
Basic
from the main menu.
2. Click
LAN IPv6
from the left side menu. Field descriptions are listed below the screen
example.
Enable Rapid Commit
Enables Rapid Commit. When enabled, the server recognizes
this option in Solicit messages sent from the DHCPv6 client.
The server and client then use a two-message exchange
(Solicit and Reply) to configure clients, rather than the default
four-message exchange (Solicit, Advertise, Request, and
Reply). This provides faster client configuration when networks
are under heavy traffic loads.
Enable Unicast
Enables Unicast, which is disabled by default. Unicast
transmission is defined to be between a single sender and a
single user over a network.
Apply
Saves changes.
Restore DhcpV6 Defaults
Restores default DHCPv6 values.
Label
Description
Page 42 / 114
Ubee Interactive
Using the DDNS Option
Ubee DVW32CB Advanced Wireless Voice Gateway Subscriber User Guide
•
January 2015
38
5.5
Using the DDNS Option
Use the dynamic domain name system (DDNS) to assign a changing IP address to a
constant pre-defined host name. The host can then be contacted by other hosts on the
Internet, even if its IP address changes.
The DDNS service for the DVW32CB is provided through a third-party and can be
purchased from Dynamic Network Services Inc. at www.dynDNS.com.
Steps
To use the DDNS option:
1.
Click
Basic
from the main menu.
2. Click
DDNS
from the left side menu. Field descriptions are listed below the screen
example.
Label
Description
Stateless Auto Configuration
IP Address
Displays the IPv6 address of the client.
MAC Address
Displays the MAC address of the client connected to the
device with an IPv6 address.
Reachability State
Displays whether the client is reachable or unreachable by
neighboring nodes.
Label
Description
DDNS Service
Enables or disables the DDNS service. When enabled, this
service is available from www.dynDNS.org.
User Name
Defines the user name for the DDNS account.
Password
Defines the password for the DDNS account.
Page 43 / 114
Ubee Interactive
Using the Static Lease Option
Ubee DVW32CB Advanced Wireless Voice Gateway Subscriber User Guide
•
January 2015
39
5.6
Using the Static Lease Option
You can use the
Static Lease
option to assign IP addresses to clients on your network
that do not change. A static lease ensures a specific device always gets the same IP
address, especially if the devices are powered on and off or disconnected and
reconnected. This may be useful in a variety of networking scenarios where you need
more control over the network and the clients connected to it. Examples is which you may
need to use a static lease include:
Using the IP Filtering Option on page 47
Using the Port Filtering Option on page 49
Using the DMZ Host Option on page 57
Steps
To assign static IP addresses:
1.
Click
Basic
from the main menu.
2. Click
Static Lease
from the left side menu. Field descriptions are listed below the
screen example.
Host Name
Defines the host name for the DDNS account.
IP Address
Displays the IP address for the DDNS account.
Status
Displays if the DDNS service is enabled or disabled.
Apply
Saves changes.
Label
Description
Page 44 / 114
Ubee Interactive
Using the Backup Option
Ubee DVW32CB Advanced Wireless Voice Gateway Subscriber User Guide
•
January 2015
40
5.7
Using the Backup Option
The Backup option lets you backup your gateway configuration or restore the DVW32CB
to a previously saved configuration.
Label
Description
Index
Provides an index number for each client that connects to your
network.
MAC Address
Defines the MAC address of the client to which you want to
assign a static IP address.
IP Address
Defines an IP address to the specific client/host.
Enabled
Activates this rule when Enable is checked.
Clear
Deletes the rule when Clear is checked.
Apply
Saves changes.
Page 45 / 114
Ubee Interactive
Using the Backup Option
Ubee DVW32CB Advanced Wireless Voice Gateway Subscriber User Guide
•
January 2015
41
Steps
To use the backup option:
1.
Click
Basic
from the main menu.
2. Click
Backup
from the left side menu.
5.7.1
Backing Up the Current Configuration
To backup and save the current device configuration, click the
Backup
button.
A pop-up window appears instructing you to select ‘Save’ when prompted. Click ‘OK’.
The following window appears, giving you the option to save the file. Click the ‘Save File’
option and click ‘OK’.
19216811.live