Page 6 / 15 Scroll up to view Page 1 - 5
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
РУССКИЙ
4
7.
Power on your cable or DSL modem. Wait until
the LEDs indicate that the modem is fully
booted up. If necessary consult with the
modem user's guide for more information.
8.
Verify that the following panel lights are on:
Power (Green), WAN (Green) and LAN (1 of
the 4)(Blinking Green).
6.
Connect the Power Adapter to the router and
then to a power outlet.
Page 7 / 15
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
РУССКИЙ
3. Configure the Router
1.
Open your web browser, type
in the Address bar, and
then press
Enter
.
2.
Enter the User Name and Password and then
click
OK
. By default:
User Name: admin
Password:
admin
Note: User name and Password are case
sensitive.
3.
Click
Quick Setup
.
6.
Configure the settings based on information
provided by your ISP. Follow the wizard
instructions to complete the configuration.
Note: Each Internet Connection type may have
different options.
4.
Select your time zone and then click
Next
.
5.
Click on the proper Internet Connection type.
Note:
1.The most common connection types are
Dynamic IP (Cable Modem) and PPPoE
(Dial-Up xDSL).
2.You may not be able to configure some
Internet Connection types or settings when
you select Quick Setup.
In this case, please
click Advanced Setup
"
WAN.
5
Page 8 / 15
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
РУССКИЙ
6
7.
Enter the Primary DNS address and Secondary
DNS address (optional). Primary and
Secondary DNS address may be provided by
your Internet Service Provider (ISP). If your ISP
does not provide you with a Primary and
Secondary DNS address, please leave these
fields blank. Then click
Next.
Your configuration is now complete
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at:
www.trendnet.com/registe
r
Thank you for choosing TRENDnet
For detailed information regarding the
TW100-S4W1CA
’s
configuration and advanced
settings, please refer to User's Guide included on the Utility CD-ROM, or TRENDnet's
8.
Click
Restart
.
9.
Wait 30 seconds while the router reboots.
10.
Open up your browser and enter in a URL
(e.g. www.trendnet.com) to verify that you
have Internet connection.
Page 9 / 15
1. I typed http://192.168.10.1 in my Internet Browser's Address Bar, but an error message
says “The page cannot be displayed.” How can I get into the TW100-S4W1CA's web
configuration page?
1. Check your hardware settings again by following the instructions in Section 2.
2. Make sure the LAN light is lit.
3. Make sure your Network adapter’s TCP/IP settings are set to
Obtain an IP address
automatically
(see the steps below).
Troubleshooting
Windows 7
Windows Vista
1
. Go into the
Control Panel
, click
Network and
Sharing Center
, click
Change Adapter Settings
and then right-click the
Local Area Connection
icon and then click
Properties
.
2
. Click
Internet Protocol Version 4(TCP/IPv4)
and
then click
Properties.
Then click on
Obtain an IP
address automatically.
1
. Go into the
Control Panel
, click
Network and
Internet
, click
Network and Sharing Center
, click
Manage Network Connections
and then right-
click the
Local Area Connection
icon and then
click
Properties
.
2
. Click
Internet Protocol Version 4(TCP/IPv4)
and
then click
Properties.
Then click on
Obtain an IP
address automatically.
Windows XP/2000
1
. Go into the
Control Panel
, double-click the
Network Connections
icon and then right-click the
Local Area Connection
icon and then click
Properties
.
7
Page 10 / 15
8
2. I am not sure what type of Internet Account Type I have for my Cable/DSL connection.
How do I find out?
Contact your Internet Service Provider's (ISP) support service for the correct information.
3. I went through the Quick Setup, but I can not get onto the Internet.
What should I do?
1. Verify that you can get onto the Internet with a direct connection into your modem.
2. Contact your ISP and verify all the information that you have in regards to your Internet
connection settings is correct.
3. Power cycle your modem and router. Unplug the power to the modem and router. Wait
30 seconds, and then reconnect the power to the modem. Wait for the modem to fully
boot up, and then reconnect the power to the router.
4. I forgot my login password.
What should I do?
Follow the instructions below:
1. Take a pin or paperclip and press the reset button on the side of the router.
2. Wait 15 seconds then let go.
This will return all settings to factory default.
The default IP address of the router is
192.168.10.1.
The default user name is “admin.
The default password is “admin”.
5. My cable ISP requires me to clone the modem computer’s MAC address.
What should I
do?
MAC address is the network device's hardware ID and consist of 12 hexadecimal characters
(e.g. 00:12:34:ab:cd:ef). Some ISPs register the subscriber's computer network adapter or
the modem's MAC address. Follow the instructions below to clone your modem or network
adapter's MAC address:
1. With the computer connected to the TW100-S4W1CA's network port, open the web
browser and enter http://192.168.10.1 into the address bar.
2. Enter the user name and password (default is admin for both user name and password)
3. Click on Advanced Setup.
4. Click on WAN on the left side of the screen.
5. Click on Dynamic IP on the left side of the screen.
6. To clone your computer's MAC address, click on “Clone MAC address”. To clone your
modem's MAC address, find the modem's MAC address and manually enter it here.
7. Click on Apply to save the settings.
If you still encounter problems or have any questions regarding the
TW100-S4W1CA
,
please
contact TRENDnet's Technical Support Department.
2
. Click
Internet Protocol (TCP/IP)
and then click
Properties.
Then
click on
Obtain an IP address
automatically.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top