1. Home
    2. /
  2. Manuals
    3. /
  3. TRENDnet
    4. /
  4. TW100-BRV204v3
    5. /
  5. 4
Page 16 / 123 Scroll up to view Page 11 - 15
Setup
13
Home Screen
After finishing or exiting the Setup Wizard, you will see the
Home
screen. When you connect
in future, you will see this screen when you connect. An example screen is shown below.
Figure 6: Home Screen
Navigation & Data Input
•
Use the menu bar on the top of the screen, and the "Back" button on your Browser, for
navigation.
•
Changing to another screen without clicking "Save" does NOT save any changes you may
have made. You must "Save" before changing screens or your data will be ignored.
Page 17 / 123
TW100-BRV204 User Guide
14
WAN Port Configuration Screen
The WAN Port Configuration screen provides an alternative to using the Wizard. It can be
accessed from the
Internet
menu. An example screen is shown below.
Figure 7: WAN Port Screen
Data - WAN Port Screen
Hostname
Normally, there is no need to change the default name, but if your
ISP requests that you use a particular “Hostname”, enter it here.
Domain name
If your ISP provided a domain name, enter it here. Otherwise, this
may be left blank.
IP Address
is assigned auto-
matically
Also called
Dynamic IP Address
.
This is the default, and the most
common.
Leave this selected if your ISP allocates an IP Address to the Wire-
less Router upon connection.
Page 18 / 123
Setup
15
Specified
IP Address
Also called
Static IP Address
.
Select this if your ISP has allocated
you a fixed IP Address. If this option is selected, the following data
must be entered.
•
IP Address
.
The IP Address allocated by the ISP.
•
Network Mask (Not required for PPPoE)
This is also supplied by your ISP. It must be compatible with the
IP Address above.
•
Gateway IP Address (Not required for PPPoE)
The address of the router or gateway, as supplied by your ISP.
•
DNS IP Address
The DNS (Domain Name Server) IP Address provided by your
ISP. If required, additional DNS entries can be made on the
Internet Options
screen.
Login Method
If your ISP does not use a login method (username, password) for
Internet access, leave this at the default value "None (Direct connec-
tion)"
Otherwise, check the documentation from your ISP, select the login
method used, and enter the required data.
•
PPPoE
- this is the most common login method, widely used
with DSL modems. Normally, your ISP will have provided some
software to connect and login. This software is no longer re-
quired, and should not be used.
•
PPTP
- this is mainly used in Europe. You need to know the
PPTP Server address as well as your name and password.
•
Big Pond Cable
- for Australia only.
•
SingTel RAS
- for Singapore only.
Login User Name
The User Name (or account name) provided by your ISP.
Login Password
Enter the password for the login name above.
RAS Plan
For SingTel customers only, select the RAS plan you are on.
Server IP Address
If using PPTP or Big Pond Cable, enter the IP address of your ISP's
server.
Connect
automatically
If Enabled (default), a connection will automatically be made as
required. If disabled, you need to establish the connection manually,
using the
Connect
button on the
Connection Details
screen (accessed
from the Status screen).
Disconnect
after Idle
Enable this if you wish an idle connection to be terminated.
If enabled, enter the idle time-out period (in minutes) in the field
provided. After the connection to your ISP has been idle for this time
period, the connection will be terminated.
If not enabled, the connection will remain open until terminated
manually, or by the remote server. (Many ISPs will terminate an idle
connection.)
Page 19 / 123
TW100-BRV204 User Guide
16
MAC Address
Also called
Network Adapter Address
or
Physical Address
. This is a
low-level identifier, as seen from the WAN port.
Normally there is no need to change this, but some ISPs require a
particular value, often that of the PC initially used for Internet access.
You can use the
Copy from PC
button to copy your PC's address into
this field, the
Default
button to insert the default value, or enter a
value directly.
Page 20 / 123
Setup
17
LAN Screen
Use the
LAN
link on the main menu to reach the
LAN
screen. An example screen is shown
below.
Figure 8: LAN Screen
Data - LAN Screen
IP Address
IP address for the TW100-BRV204, as seen from the local LAN. Use
the default value unless the address is already in use or your LAN is
using a different IP address range. In the latter case, enter an unused IP
Address from within the range used by your LAN.
Subnet Mask
The default value 255.255.255.0 is standard for small (class "C")
networks. For other networks, use the Subnet Mask for the LAN
segment to which the TW100-BRV204 is attached (the same value as
the PCs on that LAN segment).
DHCP Server
•
If Enabled, the TW100-BRV204 will allocate IP Addresses to PCs
(DHCP clients) on your LAN when they start up. The default (and
recommended) value is Enabled.
•
If you are already using a DHCP Server, this setting must be
Disabled, and the existing DHCP server must be re-configured to
treat the TW100-BRV204 as the default Gateway. See the follow-
ing section for further details.
•
The
Start IP Address
and
Finish IP Address
fields set the values
used by the DHCP server when allocating IP Addresses to DHCP
clients. This range also determines the number of DHCP clients
supported.
See the following section for further details on using DHCP.
Save
Save the data on screen.
Cancel
The "Cancel" button will discard any data you have entered and reload
the file from the TW100-BRV204.

Rate

4 / 5 based on 1 vote.

Popular TRENDnet Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top