English

4

6.

Enter a new password for your

Access Point, verify the new

password, and then click

Next.

(If a

new password is not entered, the

default password

admin

will be

used.

5.

Click

Next

.

4.

Click

Wizard

.

7.

Enter a SSID for your Access

Point and then click

Next

.

English

5

Your configuration is now complete.

For detailed information regarding the TPL-210AP's configuration, please refer

to the Troubleshooting section, User's Guide CD-ROM, or Trendnet's website

at http://www.trendnet.com.

9.

Click

Restart

.

8.

Enable Encryption if needed and

then click

Next

.

10.

Click

Close.

Q2:

A2:

Q3:

A3:

I specified the IP address http://192.168.1.200 in my Internet Browser's

Address Bar, but an error message says "The page cannot be displayed". How

can I get into the TPL-210AP's web configuration page?

First, check your hardware settings again by following the instructions in

section 2.

Second, make sure the Power, Home Plug and Wireless lights are lit.

Third, make sure the TCP/IP settings are configured properly (see Q1).

Fourth,

since the Access Point's default IP address is 192.168.1.200, make sure that no

other network devices are assigned an IP address of 192.168.1.200.

If my network's IP is different than the Access Point's range, what should I

do?

You should still configure the Access Point first. After all the settings are

applied, go to the Access Point's configuration page, click on IP setting and

change the IP address of the Access Point to match your network's IP.

6

Troubleshooting

Q1:

How do I configure TCP/IP settings on my computer?

1. Go into the

Control Panel

and double-

click the

Network Connections

icon,

right-click the

Local Area Connection

icon and then click

Properties

.

2. Click

Internet Protocol (TCP/IP)

and

then click

Properties

.

Then click on

Use the following IP address

, and

make sure you assign your network

adapter an IP address in the subnet of

192.168.1.x.

7

Q4:

A4:

Q5:

A5:

After I successfully configured the Access Point to meet my network settings,

I can not connect to my network using wireless computers.

First, if you are connecting to an existing Powerline network, the Powerline

network name one the Access Point must match that of the Powerline network.

To

configure the Powerline network name, log on to the Access Point's browser

configuration by typing in http://192.168.1.200 in the address bar of your browser.

Click

HomePlug

.

Change the HomePlug Group name to match your network's

Powerline network name.

The default HomePlug Group name is

HomePlug.

Second, verify that the power outlet the TPL-210AP is plugged into is on the same

electrical power distribution and/or circuit breaker. Third, if you have a DHCP

server in your network, you need to go into TCP/IP settings again and re-select

"Obtain an IP address automatically" to allow the PC to regain an IP address from

your DHCP server.

All the settings are correct, but I can not make a wireless connection to the

Access Point.

First, double check that the Wireless light on the Access Point is lit.

Second,

power cycle the Access Point.

Disconnect the Access Point from the power outlet,

wait 15 seconds, then plug the Access Point back into the power outlet.

Third,

contact the manufacturer of your wireless network adapter.

Make sure the

wireless network adapter is configured with the proper SSID.

The default SSID of

the Access Point is

Powerline.

If you still encounter problems or have any questions regarding the

TPL-210AP,

please

contact TRENDnet's Technical Support Department.

Certifications

This equipment has been tested and found to comply with FCC and CE Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received. Including interference that may

cause undesired operation.

NOTE:

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT.

SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO

OPERATE THE EQUIPMENT.

Waste electrical and electronic products must not

be disposed of with household waste. Please

recycle where facilities exist. Check with you Local

Authority or Retailer for recycling advice.

ADVERTENCIA

En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de

alimentacón necesario para su funcionamiento.

El uso de un adaptador distinto al

mencionado puede producir daños fisicos y/o daños al equipo conectado.

El adaptador

de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria

existente en el pais o zona de instalación.