TRENDnet TEW-692GR Router Manual PDF (Setup & Configuration Guide)

Page 6 / 21 Scroll up to view Page 1 - 5

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

РУССКИЙ

2. Hardware Installation

4

Note:

Gather all information related to your Internet Connection before you start.

If necessary,

contact your Internet Service Provider (ISP).

Cable/DSL Modem

Internet

1.

Verify that you have an Internet connection

when connecting your computer directly to the

Cable or DSL modem. Open your browser (e.g.

Internet Explorer) and type in a URL (e.g.

http://www.trendnet.com) in the address bar.

2.

Power off your cable or DSL modem.

3.

Disconnect the network cable from your Cable

or DSL modem and your computer.

4.

Connect one end of a network cable to one of

the TEW-692GR's network ports. Connect the

other end of the cable to the computer's

network port.

5.

Connect one end of a network cable to the

TEW-692GR's WAN port. Connect the other

end of the cable to your modem's network port.

Page 7 / 21

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

РУССКИЙ

5

7.

Power on your cable or DSL modem. Wait until

the LEDs indicate that modem is fully booted

up. Consult with the modem user's guide for

more information.

6.

Connect the Power Adapter to the TEW-692GR

and then to a power outlet.

Move the power

switch to the “

On

” position (EU version only).

8.

Verify that the following panel lights are on:

Power (Green), LAN (port (1,2,3,4) your

computer is connected to)(Green), WAN

(Green), Wireless (2.4GHz)(Green) and

Wireless (5GHz)(Blue)

. Please see trouble

shooting section for additional information on

LED behaviors.

Page 8 / 21

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

РУССКИЙ

6

3. Configure the Wireless Router

Note:

It is recommended that you configure the Wireless Router from a wired computer.

3.

Click

Wizard

.

1.

Open your web browser, type

http://192.168.10.1

in the Address bar, and

then press

Enter

.

2.

Enter the User Name and Password and then

click

OK

. By default:

User Name:

admin

Password:

admin

Note: User name is case sensitive.

4.

Click

Launch Internet Connection Setup

Wizard

.

5.

Click

Page 9 / 21

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

РУССКИЙ

7

10.

Click

Wizard

.

6.

Select the proper Internet Connection Type.

Configure the settings based on information

provided by your ISP. Then click Next.

Note: Each Internet Connection type may have

different options.

7.

Click

Apply

.

8.

Click

OK.

9.

Please wait while the router reboots.

11.

Click

Wireless Security Setup Wizard

.

Page 10 / 21

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

РУССКИЙ

8

12.

You will need to configure the following:

Wireless Network Name (SSID) (2.4GHz)

Wireless Network Name (SSID) (5GHz)

The SSID is the wireless network name of

your wireless network (e.g. wireless router or

access point). Enter a unique SSID. Choose

something that you would easily identify when

searching for available wireless networks.

Then click

Apply

.

Note:

1. To protect your network from any unauthorized access it is recommended to enable wireless

encryption.

2. The example below is for WPA-PSK/WPA2-PSK (AES) (Best) security.

If you select WPA-PSK

or WPA2-PSK, make sure your wireless adapters support WPA or WPA2.

If your wireless

adapters do not support WPA or WPA2, then select WEP (Good).

3. WEP encryption only supports 802.11b/g speed of up to 54Mbps.

4. Once encryption is enabled on the router, each wireless computer and device must be

configured with the same encryption key.

13.

Select

Best

and then click

Apply

.

14.

Enter characters for your wireless security

password and then click

Apply

. For

WPA-PSK or WPA2-PSK, the Pre-Shared Key

must be between 8 and 63 ASCII or 64 HEX

characters. Make sure to copy down the

Pre-Shared Key. You will need the Pre-Shared

key when you configure your wireless

adapter(s).

Rate

Popular TRENDnet Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share