Page 6 / 13 Scroll up to view Page 1 - 5
4
Note:
The example below is for WPA2-PSK security.
If you select WPA-PSK or
WPA2-PSK, make sure your wireless adapters support WPA2 or WPA.
If your wireless
adapters do not support WPA or WPA2, then select WEP.
Your Configuration is complete
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at:
www.trendnet.com/registe
r
Thank you for choosing TRENDnet
For detailed information regarding the
TEW-691GR
’s
configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or
TRENDnet's website at http://www.trendnet.com.
6.
Select the desired
WPA
mode, enter characters
for your Pre-Shared key and then click
Apply
.
For WPA-PSK or WPA2-PSK, the Pre-Shared
Key must be between 8 and 63 ASCII or 64
HEX characters.
Make sure to copy down the
Pre-Shared Key. You would have to know this
key to wirelessly connect to the TEW-691GR.
7.
Open up your browser and enter in a URL (e.g.
www.trendnet.com) to verify that you have
Internet connection.
Page 7 / 13
Troubleshooting
5
1. I typed http://192.168.10.1 in my Internet Browser's Address Bar, but an error message
says “The page cannot be displayed.” How can I get into the TEW-691GR's web
configuration page?
Check your hardware settings again by following the instructions in Section 2.
2. Make sure the LAN and WLAN lights are lit.
3. Make sure your TCP/IP settings are set to
Obtain an IP address automatically
(see the
steps below).
4. Press on the factory reset button for 15 seconds.
1.
Windows 7
1.
Go into the
Control Panel
, click
Network and
Internet
, click
Network and Sharing Center
, click
Manage Network Connections
and then right-click
the
Local Area Connection
icon and then click
Properties
.
Windows Vista
1.
Go into the
Control Panel
, click
Network and
Sharing Center
, click
Change Adapter Settings
and then right-click the
Local Area Connection
icon and then click
Properties
.
2.
Click
Internet Protocol Version 4(TCP/IPv4)
and then click
Properties.
Then
click on
Obtain an IP address automatically.
2.
Click
Internet Protocol Version 4(TCP/IPv4)
and then click
Properties.
Then
click on
Obtain an IP address automatically.
Page 8 / 13
6
2. I am not sure what type of Internet Account Type I have for my Cable/DSL connection.
How do I find out?
Contact your Internet Service Provider's (ISP) support service for the correct information.
3. I configured my router with my ISP settings, but I can not get onto the Internet.
What
should I do?
1. Verify that you can get onto the Internet with a direct connection into your modem.
2. Contact your ISP and verify all the information that you have in regards to your Internet
connection settings is correct.
3. Power cycle your modem and router.
Unplug the power to the modem and router.
Wait
30 seconds, and then reconnect the power to the modem.
Wait for the modem to fully
boot up, and then reconnect the power to the router.
4. All the settings are correct, but I can not make a wireless connection to the Router. What
should I do?
1. Make sure that the WLAN switch on the back of the router is set to on.
2. Double check that the WLAN light on the Router is lit.
3. Power cycle the TEW-691GR.
Unplug the power to the TEW-691GR.
Wait 15 seconds,
then plug the power back in to the TEW-691GR.
4. Contact the manufacturer of your wireless network adapter and make sure the wireless
network adapter is configured with the proper SSID.
The default SSID of the TEW-691GR
is
TRENDnet691.
5. When I connect a computer to the router's LAN port, I am not getting Gigabit speeds.
What should I do?
1.
Make sure that you have a Gigabit Ethernet adapter installed.
2. Make sure to use a Cat-5e or Cat 6 Ethernet cable.
Some CAT-5 cables are not rated to
run in Gigabit.
If you still encounter problems or have any questions regarding the
TEW-691GR,
please contact
TRENDnet's Technical Support Department.
1.
Go into the
Control Panel
, double-click the
Network
Connections
icon and then right-click the
Local
Area Connection
icon and then click
Properties
.
Windows XP/2000
2.
Click
Internet Protocol (TCP/IP)
and then click
Properties.
Then click on
Obtain an IP address
automatically.
Page 9 / 13
Page 10 / 13

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top