TRENDnet TEW-654TR Router Manual PDF (Setup & Configuration Guide)

Page 11 / 18 Scroll up to view Page 6 - 10

2.

Click

Internet Protocol Version

4(TCP/IPv4)

and then click

Properties.

Then

click on

Obtain an IP address

automatically.

9

Troubleshooting

Q1:

A1:

I typed http://192.168.10.1

in my Internet Browser's Address Bar, but an error

message says “The page cannot be displayed.” How can I get into the TEW-

654TR's web configuration page?

First, check your hardware settings again by following the instructions in

Section 2.

Second, make sure the LAN and WLAN lights are lit.

Third, make sure

your TCP/IP settings are set to the following:

Windows Vista

1.

Go into the

Control Panel

, double-click

the

Network Connections

icon and

then right-click the

Local Area

Connection

icon and then click

Properties

.

Windows XP/2000

1.

Go into the

Control Panel

, click

Network and Internet

, click

Network

and Sharing Center

, click

Manage

Network Connections

and then right-

click the

Local Area Connection

icon

and then click

Properties

.

Page 12 / 18

10

Fourth, press on the factory reset button for 15 seconds.

Note: If you are trying to configure the TEW-654TR in AP or AP Client mode, see

Q6.

I am not sure what type of Internet Account Type I have for my Cable/DSL

connection. How do I find out?

Contact your Internet Service Provider's (ISP) support service for the correct

information.

I went through the Wizard, but I can not get onto the Internet.

What should I

do?

First, verify that you can get onto the Internet with a direct connection into your

modem.

Second, contact your ISP and verify all the information that you have in

regards to your Internet connection settings is correct.

Third, power cycle your

modem and router.

Unplug the power to the modem and router.

Wait 30

seconds, and then reconnect the power to the modem.

Wait for the modem to fully

boot up, and then reconnect the power to the router.

I can not make a wireless connection to the TEW-654TR.

What should I do?

First, double check that the WLAN light on the Router is lit.

Second, power

cycle the TEW-654TR.

Unplug the power to the TEW-654TR.

Wait 15 seconds,

then plug the power back in to the TEW-654TR.

Third, contact the manufacturer

of your wireless network adapter and verify the steps for connecting to the TEW-

654TR via Wi-FI Protected Setup (WPS). If your wireless adapter does not support

WPS, reset the router by pressing the reset button for 15 seconds. Then configure

your wireless network adapter with the proper SSID.

The preset SSID is

TRENDnet654.

What is the USB cable for?

You can use the USB cable to power the TEW-654TR through your computer

instead of using the power adapter. Connect the power jack to the TEW-654TR

and connect one of the USB connectors into your computer.

If the USB port is not

providing enough power to the TEW-654TR, you need to connect both USB

connectors into your computer.

Q2:

A2:

Q3:

A3:

Q4:

A4:

Q5:

A5:

2.

Click

Internet Protocol (TCP/IP)

and

then click

Properties.

Then

click on

Obtain an IP address automatically.

Page 13 / 18

Q6:

A6:

How do I configure AP or AP Client mode on the TEW-654TR?

First, you need to assign a static IP address to your computer's network

adapter in the 192.168.10.X subnet.

Since the

's default IP address

is 192.168.10.100 in AP and AP Client mode when no DHCP server is connected,

do not assign an IP address of 192.168.10.100 to your computer's network

adapter.

See the instructions below:

TEW-654TR

11

2.

Click

Internet Protocol Version

4(TCP/IPv4)

and then click

Properties.

Then

click on

Use the following IP

address

, and make sure you assign

your network adapter an IP address in

the subnet of 192.168.10.x.

1.

Go into the

Control Panel

, click

Network and Internet

, click

Network

and Sharing Center

, click

Manage

Network Connections

and then right-

click the

Local Area Connection

icon

and then click

Properties

.

Windows Vista

1.

Go into the

Control Panel

, double-click

the

Network Connections

icon and

then right-click the

Local Area

Connection

icon and then click

Properties

.

Windows XP/2000

Page 14 / 18

Second, change the hardware switch on the bottom of the TEW-654TR to

AP

or

Client

.

Third, connect the provided Ethernet cable from the Ethernet port on your

computer to the Ethernet port on the TEW-654TR.

Fourth, connect the power

adapter into the TEW-654TR and plug the power adapter into an available power

outlet.

Fifth, open up your browser and enter http://654TR(AP Mode),

http://654TR-client (AP Client mode) or http://192.168.10.100

into the address bar.

Sixth, refer to the User Guide for additional instructions.

The User Guide is on the

User Guide CD-ROM drive.

12

2.

Click

Internet Protocol (TCP/IP)

and

then click

Properties.

Then click on

Use the following IP address

, and

make sure you assign your network

adapter an IP address in the subnet of

192.168.10.x.

If you still encounter problems or have any questions regarding the

TEW-654TR

,

please contact TRENDnet's Technical Support Department.

Page 15 / 18

Rate

Popular TRENDnet Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share