Page 6 / 12 Scroll up to view Page 1 - 5
English
4
5.
Enter a
Password
, verify the
Password
and then click
Next
. By
default, the
Password
is
admin
.
6.
Select your Time Zone and then
click
Next
.
7.
Click
Next
.
Note: Do not change
default settings unless it is
conflicting with your existing
hardware.
Page 7 / 12
English
5
9.
Click
Next
.
Note:
It is recommended that you enable encryption on the wireless router.
Please refer to the User Guide on the User's Guide CD-ROM for information on
setting up encryption on the wireless router.
10.
Click
Restart
.
8.
Configure the settings based on
information provided by your ISP.
Follow the wizard instructions to
complete the configuration.
Note: Each Internet Connection
type may have different options.
Page 8 / 12
English
6
Your configuration is now complete.
For detailed information regarding the
TEW-652BRP's
configuration and
advanced settings, please refer to the Troubleshooting section, User's Guide
CD-ROM, or TRENDnet's website at http://www.trendnet.com.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at:
www.trendnet.com/registe
r
Thank you for choosing TRENDnet
11.
Click
Close
.
Page 9 / 12
7
Troubleshooting
Q1:
A1:
I typed http://192.168.10.1 in my Internet Browser's Address Bar, but an error
message says “The page cannot be displayed.” How can I get into the TEW-
652BRP’s web configuration page?
First, check your hardware settings again by following the instructions in
Section 2.
Second, make sure the LAN and WLAN lights are lit.
Third, make sure
your TCP/IP settings are set to
Obtain an IP address automatically
(see the
steps below).
1.
Go into the
Control Panel
, double-click
the
Network Connections
icon and
then right-click the
Local Area
Connection
icon and then click
Properties
.
2.
Click
Internet Protocol (TCP/IP)
and
then click
Properties.
Then
click on
Obtain an IP address automatically.
Fourth, press on the factory reset button for 15 seconds.
I am not sure what type of Internet Account Type I have for my Cable/DSL
connection. How do I find out?
Contact your Internet Service Provider's (ISP) support service for the correct
information.
The Wizard does not appear.
What should I do?
First, click on Wizard on the left hand side.
Second, near the top of the
browser, “Pop-up blocked” message may
appear.
Right click on the message and
select Always Allow Pop-ups from This Site.
Third, disable your browser's pop up
blocker.
Q2:
A2:
Q3:
A3:
Page 10 / 12
8
Q4:
A4:
Q5:
A5:
I went through the Wizard, but I can not get onto the Internet.
What should I
do?
First, verify that you can get onto the Internet with a direct connection into your
modem.
Second, contact your ISP and verify all the information that you have in
regards to your Internet connection settings is correct.
Third, power cycle your
modem and router.
Unplug the power to the modem and router.
Wait 30
seconds, and then reconnect the power to the modem.
Wait for the modem to fully
boot up, and then reconnect the power to the router.
I can not make a wireless connection to the Router.
What should I do?
First, make sure that the antenna is connected to the TEW-652BRP.
Second,
double check that the WLAN light on the Router is lit.
Third, power cycle the TEW-
652BRP.
Unplug the power to the TEW-632BRP.
Wait 15 seconds, then plug the
power back in to the TEW-652BRP.
Fourth, contact the manufacturer of your
wireless network adapter and make sure the wireless network adapter is
configured with the proper SSID.
The preset SSID is TRENDnet.
If you still encounter problems or have any questions regarding the
TEW-652BRP,
please contact TRENDnet's Technical Support Department.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top