Page 6 / 13 Scroll up to view Page 1 - 5
English
4
10.
Select
Access Point
and then
click
Next
.
Note: For AP Client setup, please
refer to the User's Guide for step
by step instructions.
The User's
Guide can be found on this
product's CD-ROM.
11.
Select
Dynamic IP Address
Configuration
and then click
Configure
.
9.
Enter a password and then click
Login
.
The default password is
admin
.
12.
Select
Manual setup
and then
click
Next
.
Page 7 / 13
English
5
16.
Select the desired
WPA
mode,
enter characters for your Pre-
Shared key, keep
Cipher Type
as
TKIP and AES
and then click
Next
.
For WPA-PSK or WPA2-
PSK, the Pre-Shared Key must
be between 8 and 63 ASCII or 64
HEX characters.
Make sure to
copy down the Pre-Shared Key.
14.
Select the desired
Wireless
Mode
and then click
Next
.
15.
Select a Security Mode and then
click
Next
(example shows
WPA-PSK).
13.
Enter a SSID and then click
Next
.
By default, the SSID is
TRENDnet638
.
Page 8 / 13
English
6
19.
Click
Confirm
to apply the
settings.
18.
Give the file a name, then click
Save
(optional).
20.
Click
Exit
.
17.
Click
Save
(optional).
Page 9 / 13
English
7
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at:
www.trendnet.com/registe
r
Thank you for choosing TRENDnet
Note:
To connect a wireless computer to the TEW-638APB, refer to Question 1
in the Troubleshooting section.
Your configuration is now complete.
For detailed information regarding the
TEW-638APB's
configuration and
advanced settings, please refer to the Troubleshooting section, User's Guide
CD-ROM, or TRENDnet's website at http://www.trendnet.com.
21.
Click
Yes
to exit.
Page 10 / 13
8
Troubleshooting
Q1:
A1:
A2:
A3:
A4:
A5:
All the settings are correct, but I can not make a wireless connection to the Access
Point.
First, double check that the wireless LED on the Access Point is lit.
Second, power cycle
the Access Point.
Unplug the power to the Access Point.
Wait 15 seconds, then plug the
power back in.
Third, contact the manufacturer of your wireless network adapter.
Make sure
the wireless network adapter is configured with the proper SSID.
The default SSID of the
Access Point is
TRENDnet638.
If you have enabled any encryption on the Access Point,
make sure to configure the wireless network adapter with the same Pre-shared key.
: I am trying to connect additional wireless adapters, but I don't remember the encryption
(network) key.
What should I do?
From a wired computer, log on to the access point configuration page.
Click
Wireless ->
Security
.
The encryption key will be listed here.
: I have a wireless adapter that supports WiFi Protected Setup (WPS) push button setup.
How do I setup WPS between the
TEW-638APB and my wireless adapter?
First, press on the
WPS
button on the front of the TEW-638APB for 10 seconds.
Second, refer to your wireless adapters for instructions on setting up WPS.
: I followed the Quick Installation Guide and setup a new password.
When I log in to the
browser configuration an access error message appears.
What should I do?
The default user name is
admin
and the default password is
admin
.
When you log in to
the browser configuration for the first time, make sure to enter
admin
for user name.
Do not
leave the user name field blank.
: How do I configure AP mode on the TEW-638APB?
Please refer to the User Guide.
The User Guide is on the Utility CD-ROM drive.
Q2
Q3
Q4
Q5
If you still encounter problems or have any questions regarding the
TEW-638APB,
please contact TRENDnet's Technical Support Department.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top