Page 6 / 12 Scroll up to view Page 1 - 5
4
6.
Click on
Use the following IP address.
Enter 192.168.1.50 for IP
address and 255.255.255.0 for Subnet, then click
OK
.
7.
Click
OK.
8.
Your computer is now ready to access and configure the Access Point.
5.
Under the
General
tab, locate and select
Internet Protocol TCP/IP
and
then click
Properties
. The Internet Protocol (TCP/IP) Properties box will
appear.
English
Page 7 / 12
5
4. Configure the Access Point
From a Wired Computer
1.
Open a web browser (Internet Explorer or Netscape) and enter
http://192.168.1.250 at the address bar, then press the
Enter
key.
Leave the
username
field blank, and type
admin
for your
password
.
If you are configuring the TEW-510APB through a wired computer, follow steps
1-3.
If you are configuring the TEW-510APB through a wireless computer,
follow steps 4-7.
English
2.
Click Wireless. Enter any
AP Name
for your Access Point. Create a SSID
that your wireless network will be using, and select a channel. (For example:
Wireless AP, Home AP, or Office AP).
Scroll down to the bottom of the page
and click
Apply
.
Page 8 / 12
6
3.
Click
Setup
.
If your current network belongs to a different network segment
(i.e. 192.168.0.1~254), please type an IP address, Subnet Mask, and a
Default Gateway (i.e. Router's IP Address).
Click
Apply
.
If you are content
with the TEW-510APB's current settings, please proceed to the next section.
English
From a Wireless Computer
(using TRENDnet's TEW-501PC as example in this section)
The default settings of the Access Point are:
SSID
wlan-a
Channel - 6
4.
On your wireless computer, open up your Wireless Utility Program.
5.
Click
AP List
, select
wlan-a
, and click
Connect
.
Page 9 / 12
7
English
6.
Click
Link Information
and verify that your wireless PC is communicating
with the TEW-510APB.
7.
Go to the beginning of section
4. Configure the Access Point
and follow
steps 1-3.
Page 10 / 12
8
Troubleshooting
Q1:
A1:
Q2:
A2:
Q3.
A3:
Q4.
A4:
I specified the IP address http://192.168.1.100 in my internet
browser's address bar, but error message says "The page cannot be
displayed". How can I get into the TEW-510APB's web configuration
page?
Please check your hardware and TCP/IP settings again by following
the instructions
sections 1~3, make sure the Power, WAN, WLAN on the
Access Point's front panel are on and the TCP/IP configurations are correct.
then try accessing http://192.168.1.100 again.
If my network's IP is different than the Access Point's range, what
should I do?
You should still configure the access point first. After all the settings
are applied, go to the Access Point's configuration page, click on TCP/IP
settings and change an IP address for the Access Point to match your
network's IP.
After I successfully configured the Access Point to meet my network
settings, I cannot connecting to my network using wireless computers.
If you have a DHCP server in your network, you need to go into TCP/IP
settings again and re-select #Obtain an IP automatically# for
Windows 98/ME and #Obtain an IP Address automatically# for Windows
2000/XP to allow the PC to regain an IP address from your DHCP server.
All the settings are set correct, but I still can't use the Access Point,
what should I do?
You can find additional information in the User's Guide. If you still have
Problems,
contact our Technical Support by email or phone.
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received.
Including interference that may cause undesired operation.
NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top