Page 6 / 17
Scroll up to view Page 1 - 5
4
3. Configure the Modem
Note:
It is recommended that you configure the Modem from a wired computer.
1.
Open your web browser, type
in the Address bar, and
then press
Enter
.
2.
Enter the User Name and
password and then click
OK
.
By default:
User name: admin
Password: admin
Note: User name and Password is case
sensitive.
3.
Click
Setup
Wizard
.
Page 7 / 17
5
Note:
1. The example below is for Auto-detect.
If the Setup Wizard could not automatically
detect your Internet connection, select
Manual Selection
and input the information
using the information provided by your ISP.
2. In the example below, the ADSL connection is PPPoE
6.
Configure the settings based on information
provided by your ISP. Then click
Next
.
5.
Select the
Channel Mode
and then click
Next
.
4.
Select
Auto-detect
and then click
Next
.
Page 8 / 17
6
Note
: For other connection methods, follow the on screen instructions after you select
auto-detect.
7.
Please wait while the TEW-436BRM reboots.
8.
Check
Test Internet Connection
, and then
click
Finish
.
9.
Verify that the test has completed successfully.
Check that the ADSL and Internet LEDs are lit.
Then click
Close
.
10.
Open up your browser and enter in a URL
(e.g. www.trendnet.com) to verify that you
have Internet connection.
Page 9 / 17
4. Setting up Encryption
7
2.
This example below is WPA2-PSK.
Select the
following:
Encryption: WPA2(AES) WPA Authentication
Mode: Personal (Pre-Shared Key) Pre-Shared
Key Format: Passphrase
Pre-Shared Key: Enter an encryption key.
For Example: trendnet
Then click
Apply Changes.
For WPA-PSK or
WPA2-PSK, the Pre-Shared Key must be
between 8 and 63 ASCII or 64 HEX characters.
Make sure to copy down the encryption key.
Your Configuration is complete
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at:
www.trendnet.com/registe
r
Thank you for choosing TRENDnet
For detailed information regarding the
TEW-436BRM’s
configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide CD-ROM, or TRENDnet's website
1.
Click
Setup -> Wireless
->
Security
.
Page 10 / 17
“The page cannot be displayed.” How can I get into the TEW-436BRM's web configuration
page?
heck your hardware settings again by following the instructions in Section 2.
2. Make sure the Power, LAN and WLAN lights are lit.
3. Make sure your TCP/IP settings are set to
Obtain an IP address automatically
(see the steps below).
1. C
4. Reset the TEW-436BRM.
To reset the TEW-436BRM, take a pin or paperclip and press
the reset button on the back of the Wireless Modem for 15 seconds.
Then let go.
Troubleshooting
8
Windows Vista
Windows XP/2000
1.
Go into the
Control Panel
, click
Network and
Internet
, click
Network and Sharing Center
,
click
Manage Network Connections
and
then right-click the
Local Area Connection
icon and then click
Properties
.
2.
Click
Internet Protocol Version 4 (TCP/IPv4)
and then click
Properties.
Then click on
Obtain an IP address automatically.
1.
Go into the
Control Panel
, double-click the
Network Connections
icon and then right-
click the
Local Area Connection
icon and
then click
Properties
.
2.
Click
Internet Protocol (TCP/IP)
and then
click
Properties.
Then click on
Obtain an IP
address automatically.
19216811.live