Page 6 / 10 Scroll up to view Page 1 - 5
4
4.
Click
Discovery
, and then double-click the
Switch
that appears in the
Discovery List
.
5.
Click the
Switch
in the
Monitor List
and then
click
Configuration setting
.
7.
Click
OK
.
6.
Configure the
IP Address
,
Subnet mask
,
Gateway
, and
Password
. Click
Set
.
Page 7 / 10
5
8.
Click
Access Web
.
9.
Type in your
Password
and then click
Login
.
By default, the Password is
admin
.
Your installation is now complete.
For detailed information regarding the
Web-based Smart Utility
configuration and advanced
settings, please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or
TRENDnet's website at http://www.trendnet.com.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at:
www.trendnet.com/registe
r
Thank you for choosing TRENDnet
Page 8 / 10
1.
1.
After connecting the TEG-160WS/TEG-240WS to a power outlet, the LEDs do
not turn on.
Check the connection of the power cord to the TEG-160WS/TEG-240WS and the
power outlet. Also check that the power outlet is receiving power.
2. After installing the Web-Management Utility, I clicked Discovery and the Utility
is unable to discover the TEG-160WS/TEG-240WS. What should I do?
Make sure that the TEG-160WS/TEG-240WS is powered on and that all
connections are secure.
2. Also check that your computer's IP Address is on the same network segment as
the TEG-160WS/TEG-240WS. The default IP Address of the
TEG-160WS/TEG-240WS is
and the default password is
"admin".
3. When I access the TEG-160WS/TEG-240WS using a web browser, I get a screen
that tells me “only one user can login”. What should I do?
Another computer is configuring the TEG-160WS/TEG-240WS.
Please wait until
the user logs off. If the other user has already logged off and you still get the same
screen, then disconnect the power cord from the TEG-160WS/TEG-240WS, wait
for 5 seconds, reconnect the power cord to the TEG-160WS/TEG-240WS, allow 5
seconds for the Switch to power on, and then attempt to access the web
configuration page to login.
4. I forgot the administration password.
How do I reset my TEG-160WS/TEG-
240WS?
Press on the reset button using a pen or paperclip for 10 seconds.
The default
password is
admin
.
5.When I connect a computer to the Switch's gigabit port, the LINK/ACT LED turns
on, but the 1000Mbps (TEG-160WS) or the SPEED (TEG-240WS) LED remains off.
1.
For the TEG-160WS, when the 1000Mbps LED remains off, the computer's
connection speed is 10Mbps or 100Mbps (if the 100Mbps LED is on).
2. For the TEG-240WS, if the SPEED LED is off, the computer's connection speed is
10Mbps.
When the SPEED LED is yellow, the computer's connection speed is
100Mbps.
Make sure that you have a Gigabit Ethernet adapter installed.
Also
make sure to use a Cat-5e or Cat 6 Ethernet cable.
If you still encounter problems or have any questions regarding the TEG-160WS/TEG-
240WS, please refer to the User's Guide included on the Utility CD-ROM or contact
Trendnet's Technical Support Department.
Troubleshooting
6
Page 9 / 10
Page 10 / 10
Copyright ©2010. All Rights Reserved. TRENDnet.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top