TP-Link TL-WR720N Router Manual PDF (Setup & Configuration Guide)

Page 21 / 109 Scroll up to view Page 16 - 20

TL-WR720N

150Mbps Wireless N Router

Figure 3-9

Quick Setup – Wireless

¾

Wireless Radio -

Enable or disable the wireless radio by choosing from the drop-down

list.

¾

SSID -

Enter a value of up to 32 characters. The same name of SSID (Service Set

Identification) must be assigned to all wireless devices in your network. Considering

your wireless network security, the default SSID is set to be TP-LINK_XXXXXX

(XXXXXX indicates the last unique six numbers of each Router’s MAC address). This

value is case-sensitive. For example,

TEST

is NOT the same as

test

.

¾

Region

-

Select your region from the drop-down list. This field specifies the region

where the wireless function of the Router can be used. It may be illegal to use the

wireless function of the Router in a region other than one of those specified in this field. If

your country or region is not listed, please contact your local government agency for

assistance.

¾

Channel -

This field determines which operating frequency will be used. The default

channel is set to

Auto

, so the AP will choose the best channel automatically. It is not

necessary to change the wireless channel unless you notice interference problems with

another nearby access point.

¾

Mode -

This field determines the wireless mode which the Router works on.

¾

Channel Width -

Select any channel width from the drop-down list. The default setting

is automatic, which can automatically adjust the channel width for your clients.

¾

Disable Security -

The wireless security function can be enabled or disabled. If

disabled, the wireless stations will be able to connect the Router without encryption. It is

strongly recommended that you choose one of following options to enable security.

¾

WPA-PSK/WPA2-PSK -

Select WPA based on pre-shared passphrase.

-13-

Page 22 / 109

TL-WR720N

150Mbps Wireless N Router

z

PSK Password

- You can enter

ASCII

or

Hexadecimal

characters.

For

ASCII

, the key can be made up of any numbers from 0 to 9 and any letters from

A to Z, and the length should be between 8 and 63 characters.

For

Hexadecimal

, the key can be made up of any numbers from 0 to 9 and letters

from A to F, and the length should be between 8 and 64 characters.

Please also note the key is case sensitive, which means that upper and lower case

keys will affect the outcome. It would also be a good idea to write down the key and

all related wireless security settings.

¾

No Change -

If you choose this option, wireless security configuration will not change!

These settings are only for basic wireless parameters. For advanced settings, please refer to

Section 4.6: “Wireless

”.

6.

Click the

Finish

page.

If you don’t make any changes on the

Wireless

page, you will see the

Finish

page as shown

in Figure 3-10. Click the

Finish

button to finish the

Quick Setup

.

Figure 3-10

Quick Setup – Finish

If there is something changed on the

Wireless

page, you will see the

Finish

page as shown

in Figure 3-11. Click the

Reboot

button to make your wireless configuration take effect and

finish the

Quick Setup

.

Figure 3-11

Quick Setup - Finish

-14-

Page 23 / 109

TL-WR720N

150Mbps Wireless N Router

Chapter 4. Configuring the Router

This chapter will show each Web page's key functions and the configuration way.

4.1

Login

After your successful login, you will see the main menu on the left of the Web-based utility. On the

right, there are the corresponding explanations and instructions.

The detailed explanations for each Web page’s key function are listed below.

4.2

Status

The Status page provides the current status information about the Router. All information is

read-only.

-15-

Page 24 / 109

TL-WR720N

150Mbps Wireless N Router

Figure 4-1

Router Status

4.3

Quick Setup

Please refer to

Section 3.2: "Quick Installation Guide"

.

4.4

WPS

This section will guide you to add a new wireless device to an existing network quickly by WPS

(Wi-Fi Protected Setup)

function.

a).

Choose menu “WPS”, and you will see the next screen (shown in Figure 4-2 ).

-16-

Page 25 / 109

TL-WR720N

150Mbps Wireless N Router

Figure 4-2

WPS

¾

Current SSID –

The router supports multi-SSID and you can choose one SSID which you

want to configure its WPS function from the drop-down list. For example, if your wireless

client wants to connect to one of the router’s SSID “TP-LINK_E3C860” by WPS

，

you should

select TP-LINK_E3C860 as Current SSID.

¾

WPS Status -

Enable or disable the WPS function here.

¾

Current PIN -

The current value of the Router's PIN is displayed here. The default PIN of the

Router can be found in the label or User Guide.

¾

Restore PIN -

Restore the PIN of the Router to its default.

¾

Gen New PIN -

Click this button, and then you can get a new random value for the Router's

PIN. You can ensure the network security by generating a new PIN.

¾

Add device -

You can add a new device to the existing network manually by clicking this

button.

b).

To add a new device:

If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless

connection between wireless adapter and Router using either Push Button Configuration (PBC)

method or PIN method.

)

Note:

To build a successful connection by WPS, you should also do the corresponding configuration of

the new device for WPS function meanwhile.

I.

Use the Wi-Fi Protected Setup Button

Use this method if your client device has a Wi-Fi Protected Setup button.

Step 1:

Press the WPS button on the back panel of the Router.

You can also keep the default WPS Status as

Enabled

and click the

Add device

button

in Figure 4-2, then Choose “

Press the button of the new device in two minutes

” and

click

Connect

. (Shown in the following figure)

-17-

Rate

Popular TP-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share