1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TL-WR720N
    5. /
  5. 4
Page 16 / 109 Scroll up to view Page 11 - 15
TL-WR720N
150Mbps Wireless N Router
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your
150Mbps Wireless N
Router using
Quick Setup
Wizard
within minutes.
3.1
TCP/IP Configuration
The default domain name of the
150Mbps Wireless N Router is
http://tplinklogin.net
, the default
IP address is 192.168.0.1, and the default Subnet Mask is 255.255.255.0. These values can be
changed as you desire. In this guide, we all use the default values for description.
Connect the local PC to the LAN ports of the Router, and then you can configure the IP address
for your PC by following the steps below:
1)
Set up the TCP/IP Protocol in "
Obtain an IP address automatically
" mode on your PC.
If you need instructions as to how to do this, please refer to
Appendix B: "Configuring the
PC."
2)
Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the
command prompt
to verify the network connection
between your PC and the Router. The following example is in Windows XP OS.
Open a command prompt, and type
, and then press
Enter
.
¾
If the result displayed is similar to the
Figure 3-1
, it means the connection between your PC
and the Router has been established well.
Figure 3-1
Success result of Ping command
-8-
Page 17 / 109
TL-WR720N
150Mbps Wireless N Router
¾
If the result displayed is similar to the
Figure 3-2,
it means the connection between your PC
and the Router failed.
Figure 3-2
Failure result of Ping command
Please check the connection following these steps:
1.
Is the connection between your PC and the Router correct?
)
Note:
The 1/2 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter should
be lit.
2.
Is the TCP/IP configuration for your PC correct?
)
Note:
If the Router's IP address is 192.168.0.1, your PC's IP address must be within the range of
192.168.0.2 ~ 192.168.0.254.
3.
Try the IP address 192.168.1.1.
)
Note:
If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the
Router will automatically switch from 192.168.0.1 to 192.168.1.1 to avoid IP conflict. Therefore, in
order to verify the network connection between your PC and the Router, you can open a
command prompt, and type
ping 192.168.1.1
, and then press
Enter
.
3.2
Quick Installation Guide
With a Web-based (Internet Explorer or Netscape
®
Navigator) utility, it is easy to configure and
manage the 150Mbps Wireless N Router. The Web-based utility can be used on any Windows,
Macintosh or UNIX OS with a Web browser.
-9-
Page 18 / 109
TL-WR720N
150Mbps Wireless N Router
1.
To access the configuration utility, open a web-browser and type the default address
http://tplinklogin.net
in the address field of the browser.
Figure 3-3
Login the Router
After a moment, a login window will appear, similar to the Figure 3-4. Enter
admin
for the User
Name and Password, both in lower case letters. Then click the
OK
button or press the
Enter
key.
Figure 3-4
Login Windows
)
Note:
If the above screen does not pop up, it means that your Web-browser has been set to a proxy. Go
to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel
the Using Proxy checkbox, and click
OK
to finish it.
2.
After successfully log in, you can click the
Quick Setup
to quickly configure your Router.
Figure 3-5
Quick Setup
3.
Click
Next
, and then
WAN Connection Type
page will appear as shown in Figure 3-6.
-10-
Page 19 / 109
TL-WR720N
150Mbps Wireless N Router
Figure 3-6
Choose WAN Connection Type
The Router provides
Auto-Detect
function and supports three popular ways
PPPoE
,
Dynamic IP
and
Static IP
to connect to the Internet. It’s recommended that you make use of
the
Auto-Detect
function. If you are sure of what kind of connection type your ISP provides,
you can select the very type and click
Next
to go on configuring.
4.
If you select
Auto-Detect
, the Router will automatically detect the connection type your ISP
provides. Make sure the cable is securely plugged into the WAN port before detection. The
appropriate configuration page will be displayed when an active Internet service is
successfully detected by the Router.
¾
If the connection type detected is
PPPoE
, the next screen will appear as shown in
Figure 3-7.
Figure 3-7
Quick Setup – PPPoE
¾
User Name and Password -
Enter the
User Name
and
Password
provided by your ISP.
These fields are case sensitive. If you have difficulty with this process, please contact
your ISP.
¾
Confirm Password -
Re-enter the password provided by your ISP to ensure the
Password you entered is correct. If the Password is different from the Confirm Password,
the screen will appear as shown below. Click
OK
, and re-enter the Password
and
Confirm Password.
-11-
Page 20 / 109
TL-WR720N
150Mbps Wireless N Router
¾
If the connection type detected is Dynamic IP, the next screen will appear as shown in
Figure 3-9.
¾
If the connection type detected is Static IP, the next screen will appear as shown in
Figure 3-8.
Figure 3-8
Quick Setup - Static IP
¾
IP Address -
This is the WAN IP address seen by external users on the Internet
(including your ISP). Enter the IP address into the field.
¾
Subnet Mask -
The Subnet Mask is used for the WAN IP address, it is usually
255.255.255.0.
¾
Default Gateway -
Enter the gateway IP address into the box if required.
¾
Primary
DNS -
Enter the DNS Server IP address into the box if required.
¾
Secondary DNS -
If your ISP provides another DNS server, enter it into this field.
5.
Click
Next
to continue, the Wireless settings page will appear as shown in Figure 3-9.
-12-

Rate

4.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top