1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TL-WR720N
    5. /
  5. 3
Page 11 / 109 Scroll up to view Page 6 - 10
TL-WR720N
150Mbps Wireless N Router
1.3
Main Features
¾
Make use of IEEE 802.11n wireless technology to provide a wireless data rate of up to
150Mbps
¾
One 10/100M Auto-Negotiation RJ45 WAN port, two 10/100M Auto-Negotiation RJ45 LAN
ports supporting Auto MDI/MDIX
¾
Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security
¾
Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet
access
¾
Up to 4 SSIDs supporting multiple wireless networks with different SSIDs and passwords
¾
Supports Virtual Server, Special Application and DMZ host
¾
Supports UPnP, Dynamic DNS
¾
Provides Automatic-connection and Scheduled Connection on certain time to the Internet
¾
Connects Internet on demand and disconnects from the Internet when idle for PPPoE
¾
Built-in NAT and DHCP server supporting static IP address distributing
¾
Supports Stateful Packet Inspection
¾
Supports Parental Control and Access Control
¾
Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control
List)
¾
Supports Flow Statistics
¾
Supports firmware upgrade and Web management
-3-
Page 12 / 109
TL-WR720N
150Mbps Wireless N Router
1.4
Panel Layout
1.4.1
The Front Panel
Figure 1-1
Front Panel sketch
The Router’s LEDs and the WPS button are located on the front panel (View from left to right).
Name
Status
Indication
Off
Power is off.
（
Power
）
On
Power is on.
Flashing
The Router is working properly.
(System)
On /Off
The Router has a system error.
Off
The Wireless function is disabled.
(WLAN)
Flashing
The Wireless function is enabled.
Off
There is no device linked to the corresponding port.
On
There is a device linked to the corresponding port but
there is no activity.
(LAN1,2)
(WAN),
Flashing
There is an active device linked to the corresponding port.
Slow Flash
A wireless device is connecting to the network by WPS
function. This process will last in the first 2 minutes.
On
A wireless device has been successfully added to the
network by WPS function.
(WPS)
Quick Flash
A wireless device failed to be added to the network by
WPS function.
Table 1-1 The LEDs description
)
Note:
After a device is successfully added to the network by WPS function, the WPS LED will keep on
for about 5 minutes and then turn off.
-4-
Page 13 / 109
TL-WR720N
150Mbps Wireless N Router
1.4.2
The Rear Panel
Figure 1-2
Rear Panel sketch
The following parts are located on the rear panel (View from left to right).
¾
WPS/RESET:
This button is used for both WPS and Reset function. To use the WPS function,
press it for less than five seconds; to use the RESET function, press it for more than five
seconds.
z
Used as RESET button:
There are two ways to reset to the Router's factory defaults:
1)
Use the
Factory Defaults
function on
System Tools
->
Factory Defaults
page in the
Router's Web-based Utility.
2)
Use the Factory Default Reset button: With the Router powered on, press and hold the
RESET
button (at least 5 seconds) until the SYS LED becomes quick-flash from
slow-flash. Then release the button and wait the Router to reboot to its factory default
settings.
z
Used as WPS button:
WPS:
If you have client devices, such as wireless adapters, that support Wi-Fi Protected
Setup, then you can press this button to quickly establish a connection between the Router
and client devices and automatically configure wireless security for your wireless network.
¾
POWER:
The Power socket is where you will connect the power adapter. Please use the
power adapter provided with this TL-WR720N 150Mbps Wireless N Router.
¾
WAN:
The WAN port is where you will connect the DSL/cable Modem, or Ethernet.
¾
LAN (1-2):
These ports connect the Router to the local PC(s).
-5-
Page 14 / 109
TL-WR720N
150Mbps Wireless N Router
Chapter 2. Connecting the Router
2.1
System Requirements
¾
Broadband Internet Access Service (DSL/Cable/Ethernet)
¾
One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is
connected directly to the Ethernet.)
¾
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
¾
TCP/IP protocol on each PC
¾
Web browser, such as Microsoft Internet Explorer 5.0 , Netscape Navigator 6.0 or above
2.2
Installation Environment Requirements
¾
Place the Router in a well ventilated place far from any heater or heating vent
¾
Avoid direct irradiation of any strong light (such as sunlight)
¾
Keep at least 2 inches (5 cm) of clear space around the Router
¾
Operating Temperature: 0
~40
(32
~104
)
℃
℃
℉
℉
¾
Operating Humidity: 10%~90%RH, Non-condensing
2.3
Connecting the Router
Before installing the Router, make sure your PC is connected to the Internet through the
broadband service successfully. If there is any problem, please contact your ISP. After that, please
install the Router according to the following steps. Don't forget to pull out the power plug and keep
your hands dry.
1.
Power off your PC, Cable/DSL Modem, and the Router.
2.
Locate an optimum location for the Router. The best place is usually at the center of your
wireless network. The place must accord with the
Installation Environment Requirements
.
3.
Connect the PC(s) and each Switch/Hub in your LAN to the LAN Ports on the Router, shown
in
Figure 2-1
. (If you have the wireless NIC and want to use the wireless function, you can
skip this step.)
4.
Connect the DSL/Cable Modem to the WAN port on the Router, shown in
Figure 2-1.
5.
Connect the power adapter to the power socket on the Router, and the other end into an
electrical outlet. The Router will start to work automatically.
-6-
Page 15 / 109
TL-WR720N
150Mbps Wireless N Router
6.
Power on your PC and Cable/DSL Modem.
Figure 2-1
Hardware Installation of the 150Mbps Wireless N Router
-7-

Rate

4.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top