TP-Link TL-MR3020 Router Manual PDF (Setup & Configuration Guide)

Page 206 / 258 Scroll up to view Page 201 - 205

TL-MR3020

Portable 3G/4G Wireless N Router

The WPS Configuration Screen of Wireless Adapter

II. By PIN

If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the

network by PIN with the following two methods.

Method One:

Enter the PIN into my AP

Step 1: Keep the default WPS Status as

Enabled

and click the

Add device

button in Figure

6-2, then the following screen will appear.

Step 2: Choose “

Enter the new device's PIN

” and enter the PIN code (take 16952898 for

example) of the wireless adapter in the field as shown in the figure above. Then click

Connect.



Note:

The PIN code of the adapter is always displayed on the WPS configuration screen as shown in

the following figure.

Step 3: For the configuration of the wireless adapter, please choose “

Enter a PIN into my

access point or a registrar

”

in the

configuration utility of the WPS as below, and click

Next.

-195-

Page 207 / 258

TL-MR3020

Portable 3G/4G Wireless N Router

The WPS Configuration Screen of Wireless Adapter



Note:

le, the default PIN code of this adapter is 16952898 as the above figure shown.

AP in Figure 6-2 (each AP has its unique PIN code.

Here takes the PIN code 12345670 of this AP for example).

the WPS as below, and enter the PIN code

of the AP into the field after “

Access Point PIN

”. Then click

In this examp

Method Two:

Enter the PIN from my AP

Step 1: Get the Current PIN code of the

Step 2: For the configuration of the wireless adapter, please choose “

Enter a PIN from my

access point

”

in the

configuration utility of

The WPS Configuration Screen of Wireless Adapter

-196-

Page 208 / 258

TL-MR3020

Portable 3G/4G Wireless N Router



Note:

The default PIN code of the AP can be found in its label or the WPS configuration screen as

Figure 6-2.

You will see the following screen when the new device has successfully connected to the

network.



Note:

1)

The WPS LED on the AP will light green for five minutes if the device has been successfully

on of the AP is disabled.

added to the network.

2)

The WPS function cannot be configured if the Wireless functi

Please make sure the Wireless function is enabled before configuring the WPS.

6.5 Network

Figure 6-4

the Network menu

There is one submenu under the Network menu (shown in Figure 6-4):

LAN

.

Click it and you

will be able to configure the LAN function.

The

Network

option allows you to customize your local network manually by changing the

default settings of the AP.

Selecting

Network

will enable you to configure the IP parameters of Network on this page.

-197-

Page 209 / 258

TL-MR3020

Portable 3G/4G Wireless N Router

Figure 6-5 LAN



MAC Address

-

The physical address of the AP. The value can't be changed.



Type -

Select

Dynamic IP

to get IP address from DHCP server or select

Static IP

to

re IP address manually from the drop-down list.

lt



Subnet Mask -

An address code that determines the size of the network. Normally use

1)

If you change the IP Address, you must use the new IP Address to log in the AP.

2)

If the new LAN IP Address you set is not in the same subnet with the IP Address pool of

D

ill not take effect until it is re-configured accordingly.

solution for your wireless network. Here you can create a wireless

local area network just through a few settings. Wireless Settings is used for the configuration of

to

secure your data and thus provide greater security for your wireless network. MAC filtering

allows you to control the access of wireless stations to the AP. Wireless Advanced allows you to

configure some advanced parameters for the AP. Throughput Monitor helps to watch wireless

throughput information Wireless statistics enables you to get detailed information about the

current connected wireless stations.

There are six submenus under the Wireless menu (shown in Figure 6-6):

Wireless Settings

,

Wireless Security

,

Wireless MAC Filtering

,

Wireless Advanced

and

Wireless Statistics

.

configu



IP Address -

Enter the IP address of your AP in dotted-decimal notation (factory defau

setting is 192.168.0.254).

255.255.255.0 as the subnet mask.



Gateway

-

The gateway should be in the same subnet as your IP address.



Note:

HCP sever, the IP Address pool w

6.6 Wireless

The

Wireless

option, improving functionality and performance for wireless network, can help

you make the AP an ideal

some basic parameters of the AP. Wireless Security provides three different security types

-198-

Page 210 / 258

TL-MR3020

Portable 3G/4G Wireless N Router

Click any of them, and you will be able to configure the corresponding function. The detailed

explanations for each submenu are provided below.

Figure 6-6 Wireless menu

6.6.1

Wireless Settings

Selecting

Wireless

>

Wireless Settings

to configure the basic settings for your

figure the

setting options for each operation

less stations to access this device.

will enable you

wireless network on the screen below (Figure 6-7).This page allows you to con

wireless mode for your device. Six operation modes are supported here, including

Access

Point

,

Client

,

Repeater

and

Bridge with AP

. The available

mode are different from those of the other.

1) Access Point:

This mode allows wire

Figure 6-7 Wireless Settings in Access Point mode



Wireless Network Name (also called SSID) -

Identifies your wireless network name. Creat

a name up to 32 characters and make sure all wireless points in the wireless network with the

same SSID. The default SSID is TP-LINK_POCKET_3020_XXXXXX (XXXXXX indicates the

last unique six characters of eac

e

h device’s MAC address). This value is case-sensitive. For

example,

TEST

is NOT the same as

test

.

-199-

Rate

Popular TP-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share