1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W8961NT
    5. /
  5. 6
Page 26 / 87 Scroll up to view Page 21 - 25
TD-W8961ND
300Mbps Wireless N ADSL2+ Modem Router User Guide
18
Figure 4-4
¾
Interface:
You can select
Ethernet
,
ADSL
and
WLAN
to view the corresponding network
traffic over different ports.
¾
Select
Ethernet
, and you
will
see the statistics table as below.
Statistics Table:
Transmit Frames
The frames transmitted over the Ethernet port.
Transmit Multicast Frames
The multicast frames transmitted over the Ethernet
port.
Transmit total Bytes
The total bytes transmitted over the Ethernet port.
Transmit Collision
The collision occurred over the Ethernet port when
data is being transmitted.
Transmit
Statistics
Transmit Error Frames
The error frames over the Ethernet port when data is
being transmitted.
Receive Frames
The frames received over the Ethernet port.
Receive Multicast Frames
The multicast frames received over the Ethernet port.
Receive total Bytes
The total bytes received over the Ethernet port.
Receive CRC Errors
The CRC errors occurred over the Ethernet port when
data is being received.
Receive
Statistics
Receive Under-size Frames
The Under-size frames received over the Ethernet
port.
Downloaded from
www.Manualslib.com
manuals search engine
Page 27 / 87
TD-W8961ND
300Mbps Wireless N ADSL2+ Modem Router User Guide
19
¾
Select
ADSL
, and you
will
see the statistics table as below.
Statistics Table:
Transmit total PDUs
The total PDUs transmitted over the ADSL port.
Transmit
Statistics
Transmit total Error Counts
The total errors occurred over the ADSL port when data
is being transmitted.
Receive total PDUs
The total PDUs transmitted over the ADSL port.
Receive
Statistics
Receive total Error Counts
The total errors occurred over the ADSL port when data
is being received.
¾
Select
WLAN
, and you
will
see the statistics table as below.
Statistics Table:
Tx Frames Count
The frames transmitted over the WLAN when wireless data is
being transmitted.
Tx Errors Count
The errors occurred over the WLAN when wireless data is being
transmitted.
Transmit
Statistics
Tx Drops Count
The drops occurred over the WLAN when wireless data is being
transmitted.
Rx Frames Count
The frames received over the WLAN when wireless data is being
transmitted.
Rx Errors Count
The errors occurred over the WLAN when wireless data is being
received.
Receive
Statistics
Rx Drops Count
The drops occurred over the WLAN when wireless data is being
received.
Click the
REFRESH
button to refresh immediately.
4.2
Quick Start
Please refer to
" 3.2 Login"
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 28 / 87
TD-W8961ND
300Mbps Wireless N ADSL2+ Modem Router User Guide
20
4.3
Interface Setup
Choose “
Interface Setup
”, you can see the next submenus:
Internet
and
LAN
.
Figure 4-5
Click any of them, and you will be able to configure the corresponding function.
4.3.1 Internet
Back to LED Explanation
Choose “
Interface Setup
→
Internet
” menu, you can configure the parameters for WAN ports in
the next screen (shown in Figure 4-6).
Figure 4-6
¾
ATM VC:
ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path
Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup
8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP. You
need to activate the VC to take effect. For PVCs management, you can use ATM QoS to
setup each PVC traffic line's priority.
•
Virtual Circuit:
Select the VC number you want to setup, PVC0~PVC7.
Downloaded from
www.Manualslib.com
manuals search engine
Page 29 / 87
TD-W8961ND
300Mbps Wireless N ADSL2+ Modem Router User Guide
21
•
Status:
If you want to use a designed VC, you should activate it.
•
VPI:
Identifies the virtual path between endpoints in an ATM network. The valid range is
from 0 to 255. Please input the value provided by your ISP.
•
VCI:
Identifies the virtual channel endpoints in an ATM network. The valid range is from
32 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value
provided by your ISP.
•
PVCs Summary:
Click the button, and you can view the summary information about the
PVCs.
•
QoS:
Select the Quality of Service types for this Virtual Circuit, including CBR (Constant
Bit Rate), UBR (Unspecified Bit Rate) and VBR (Variable Bit Rate). These QoS types are
all controlled by the parameters specified below, including PCR (Peak Cell Rate), SCR
(Sustained Cell Rate) and MBS (Maximum Burst Size), please configure them according
to your needs.
¾
Encapsulation:
There are four connection types: Dynamic IP Address, Static IP Address,
PPPoA/PPPoE and Bridge Mode. Please choose the designed type that you want to use.
After that, you should follow the configuration below to proceed.
1)
Dynamic IP Address
Select this option if your ISP provides you an IP address automatically. This option is typically
used for Cable services. Please enter the Dynamic IP information accordingly.
Figure 4-7
¾
Encapsulation:
Select the encapsulation mode for the Dynamic IP Address, you can leave it
default.
¾
NAT:
Select this option to Enable/Disable the NAT (Network Address Translation) function
for this VC. The NAT function can be activated or deactivated per PVC basis.
Downloaded from
www.Manualslib.com
manuals search engine
Page 30 / 87
TD-W8961ND
300Mbps Wireless N ADSL2+ Modem Router User Guide
22
¾
Default Route:
If enable this function, the current PVC will be considered as the default
gateway to internet from this device.
¾
TCP MTU Option:
Enter the TCP MTU as your desire.
¾
Dynamic Route:
Select this option to specify the RIP (Routing Information protocol) version
for WAN interface, including
RIP1
,
RIP2-B
and
RIP2-M
. RIP2-B and RIP2-M are both sent in
RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast
format.
•
Direction:
Select this option to specify the RIP direction.
None
is for disabling the RIP
function.
Both
means the ADSL Router will periodically send routing information and
accept routing information, and then incorporate them into routing table.
IN only
means
the ADSL router will only accept but will not send RIP packet.
OUT only
means the
ADSL router will only send but will not accept RIP packet.
¾
Multicast:
Select IGMP version, or disable the function. IGMP (Internet Group Multicast
Protocol) is a session-layer protocol used to establish membership in a multicast group. The
ADSL ATU-R supports both IGMP version 1 (
IGMP v1
) and
IGMP v2
. Select “Disabled” to
disable it.
2)
Static IP Address
Select this option if your ISP provides static IP information to you. You should set static IP
address, IP subnet mask, and gateway address in the screen below (shown in Figure 4-8).
Figure 4-8
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top