1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W8961NT
    5. /
  5. 10
Page 46 / 87 Scroll up to view Page 41 - 45
TD-W8961ND
300Mbps Wireless N ADSL2+ Modem Router User Guide
38
Figure 4-23
Method Two:
Enter the PIN from my Router
Step 1:
Get the Current PIN code of the Router from
AP self PIN code
in Figure 4-23 (each
Router has its unique PIN code. Here takes the PIN code 55924054 of this Router
for example).
Step 2:
For the configuration of the wireless adapter, please choose “
Enter a PIN from my
access point
”
in the
configuration utility of the WPS as below, and enter the PIN
code of the Router into the field after “
Access Point PIN
”. Then click
Next
.
The WPS Configuration Screen of Wireless Adapter
)
Note:
The default PIN code of the Router can be found in its label or the WPS configuration screen
as Figure 4-23.
•
WPS progress:
Show the current WPS progress.
Downloaded from
www.Manualslib.com
manuals search engine
Page 47 / 87
TD-W8961ND
300Mbps Wireless N ADSL2+ Modem Router User Guide
39
•
SSID:
Wireless network name shared among all points in a wireless network. The SSID
must be identical for all devices in the wireless network. It is case-sensitive and must not
exceed 32 characters (use any of the characters on the keyboard). Make sure this
setting is the same for all stations in your wireless network. Type the desired SSID in the
space provided.
•
Authentication Type:
Select an authentication type from the drop-down list, which
allows you to configure security features of the wireless LAN interface. Options available
are: Disabled, WEP-64Bits, WEP-128Bits, WPA-PSK, WPA2-PSK, and WPA-PSK/
WPA2-PSK.
¾
WDS Settings:
Select On/Off to enable/disable WDS. With this function enabled, the Router
can bridge two or more WLANs.
•
MAC Address:
Enter the MAC Address you wish to bridge in the field.
¾
Wireless MAC Address Filter:
Wireless access can be filtered by using the MAC addresses
of the wireless devices transmitting within your network’s RADIUS.
•
Active:
If you wish to filter users by MAC Address, select “Activated”, and “Deactived”
for don’t.
•
Action:
To filter wireless users by MAC Address, select “Allow Association” or “Deny
Association” the follow Wireless LAN station(s) association.
•
MAC Address:
Enter the MAC Address you wish to filter in the field.
)
Note:
For most users, it is recommended to use the default Wireless LAN Performance settings. Any
changes made to these settings may adversely affect your wireless network. Under certain
circumstances, changes may benefit performance. Carefully consider and evaluate any changes
to these wireless settings.
4.4
Advanced Setup
Choose “
Advanced Setup
”, you can see the next submenus:
Figure 4-24
Click any of them, and you will be able to configure the corresponding function.
4.4.1 Firewall
Choose “
Advanced Setup
→
Firewall
” menu, and you will see the next screen (shown in Figure
4-25).
Downloaded from
www.Manualslib.com
manuals search engine
Page 48 / 87
TD-W8961ND
300Mbps Wireless N ADSL2+ Modem Router User Guide
40
Figure 4-25
¾
Firewall:
Select this option can automatically detect and block Denial of Service (DoS)
attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack.
¾
SPI:
If you enable SPI, all traffics initiated from WAN would be blocked, including DMZ,
Virtual Server, and ACL WAN side.
4.4.2 Routing
Choose “
Advanced Setup
→
Routing
” menu, and you will see the routing information in the next
screen (shown in Figure 4-26).
Figure 4-26
Click
ADD ROUTE
button to add a new route in the next screen (shown in Figure 4-27).
Figure 4-27
¾
Destination IP Address:
This parameter specifies the IP network address of the final
destination.
¾
IP Subnet Mask:
Enter the subnet mask for this destination.
Downloaded from
www.Manualslib.com
manuals search engine
Page 49 / 87
TD-W8961ND
300Mbps Wireless N ADSL2+ Modem Router User Guide
41
¾
Gateway IP Address:
Enter the IP address of the gateway. The gateway is an immediate
neighbor of your ADSL Router that will forward the packet to the destination. On the LAN, the
gateway must be a router on the same segment as your Router; over Internet (WAN), the
gateway must be the IP address of one of the remote nodes.
¾
Metric:
Metric represents the "cost" of transmission for routing purposes. IP Routing uses
hop count as the measurement of cost, with a minimum of 1 for directly connected networks.
Enter a number that approximates the cost for this link. The number need not to be precise,
but it must between 1 and 15. In practice, 2 or 3 is usually a good number.
¾
Announced in RIP:
This parameter determines if the ADSL router will include the route to
this remote node in its RIP broadcasts. If set to Yes, the route to this remote node will be
propagated to other hosts through RIP broadcasts. If No, this route is kept private and is not
included in RIP broadcasts.
4.4.3 NAT
Choose “
Advanced Setup
→
NAT
” menu, you can setup the NAT (Network Address Translation)
function for the Router (shown in Figure 4-28).
Figure 4-28
¾
Virtual Circuit:
Enter Virtual Circuit Index that you plan to setup for the NAT function.
¾
NAT Status:
This field shows the current status of the NAT function for the current VC. You
can go to the previous screen (shown in Figure 4-6) to activate the function.
¾
Number of IPs:
This field is to specify how many IPs are provided by your ISP for current VC.
It can be single IP or multiple IPs. We select Multiple to explain.
)
Note:
For VCs with single IP, they share the same DMZ and Virtual servers; for VCs with multiple IPs,
each VC can set DMZ and Virtual servers. Furthermore, for VCs with multiple IPs, they can define
the Address Mapping rules; for VCs with single IP, since they have only one IP, there is no need
to individually define the Address Mapping rule.
Downloaded from
www.Manualslib.com
manuals search engine
Page 50 / 87
TD-W8961ND
300Mbps Wireless N ADSL2+ Modem Router User Guide
42
4.4.3.1 DMZ
Choose “
Advanced Setup
→
NAT
→
DMZ
” in Figure 4-28, you can configure the DMZ host in the
next screen. A DMZ (demilitarized zone) is a host between a private local network and the outside
public network. It prevents outside users from getting direct access to a server that has company
data. Users of the public network outside the company can access to the DMZ host.
Figure 4-29
¾
DMZ Host IP Address:
Enter the specified IP Address for DMZ host on the LAN side.
4.4.3.2 Virtual Server
Choose “
Advanced Setup
→
NAT
→
Virtual Server
” in Figure 4-28, you can configure the Virtual
Server in the next screen.
The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or
FTP server, that you can make visible to the outside world even though NAT makes your whole
inside network appear as a single machine to the outside world.
Figure 4-30
¾
Rule Index:
The Virtual server rule index for this VC. You can specify 10 rules in maximum.
All the VCs with single IP will use the same Virtual Server rules.
¾
Application:
The Virtual servers can be used for setting up public services on your LAN.
¾
Protocol:
The protocol used for this application.
¾
Start
&
End port number:
Enter the specific Start and End Port number you want to forward.
If it is one port only, you can enter the End port number the same as Start port number. For
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top