1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W8960Nv1.3.6
    5. /
  5. 8
Page 36 / 122 Scroll up to view Page 31 - 35
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
6.
Select a preferred
WAN
interface as the system default gateway and click
Next
.
Figure 4-17
7.
Configure the DNS Server Addresses on the screen as follows.
Figure 4-18
)
Note:
If only single PVC with IPoA is configured, you must enter static DNS server IP addresses.
8.
On the next screen (as shown Figure 4-19) you will see the detailed settings you’ve made.
Please click the
Apply/Save
button to save these settings.
29
Page 37 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-19
4.4.2.3 ATM-EoA-Bridging
If you want to adopt the
Bridge
service and you need to use an ATM Interface, follow the steps
below to add a WAN service over a selected ATM interface:
1.
Add a new ATM interface and select
EoA
option for DSL Link Type (see
4.4.1.1
ATM
interface
).
2.
Click the
Add
button on the screen Figure 4-7. Select WAN Service Interface over ATM PVC
on the next screen (as shown Figure 4-8).
3.
Select
Bridging
option for the
WAN service type
on the screen (as shown Figure 4-9), and
click
Next
button to continue.
4.
On the screen (as shown Figure 4-13) you will see the detailed settings you’ve made. Please
click the
Apply/Save
button to save these settings.
4.4.2.4 ATM-PPPoA
If your ISP provides a
PPPoA
connection and you need to use an ATM Interface, follow the steps
below to add a WAN service over a selected ATM interface:
1.
Add a new ATM interface and select
PPPoA
option for DSL Link Type (see
4.4.1.1
ATM
interface
).
2.
Click the
Add
button on the screen Figure 4-7 and the next configuration is similar to
PPPoE
,
(see section
4.4.2.1
ATM-EoA-PPPoE
)
. The difference is that you don’t need to set the
PPPoE Service Name
and
Bridge PPPoE Frames Between WAN and Local Ports
on the
screen of Figure 4-10.
30
Page 38 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
4.4.2.5 ATM-IPoA
If your ISP provides an
IPoA
connection and you need to use an ATM Interface, follow the steps
below to add a WAN service over a selected ATM interface.
1.
Add a new ATM interface and select
IPoA
option for DSL Link Type (see
4.4.1.1
ATM
interface
).
2.
Click the
Add
button on the screen Figure 4-7 and the next configuration is similar to
IPoE
(see section
4.4.2.2
ATM-EoA-IPoE
). The difference is that you have to manually set the
Static IP Address on the screen of Figure 4-15, and the Static IP Address for DNS Server on
the screen of Figure 4-18.
)
Note:
ETH and ATM service can not coexist. If the ATM Interface had configured, you cannot configure
any other WAN service over the ETH Interface until the ATM Interface is deleted.
4.4.2.6 ETH-PPPoE
If your ISP provides a
PPPoE
connection and you need to use an
ETH
Interface, follow the steps
below to add a WAN service over a selected ETH interface:
1.
Add a new
ETH
interface on the screen of
4.4.1.2
ETH interface
.
2.
Click the
Add
button on the screen Figure 4-7 and the following configuration is similar to
PPPoE
over ATM interface
(see section
4.4.2.1
ATM-EoA-PPPoE
).
4.4.2.7 ETH-IPoE
If your ISP provides an
IPoE
connection and you want to use an
ETH
Interface, follow the steps
below to add a WAN service over a selected ETH interface:
1.
Add a new
ETH
interface on the screen of
4.4.1.2
ETH interface
.
2.
Click the
Add
button on the screen Figure 4-7 and the next configuration is similar to
IPoE
over ATM interface
(see section
4.4.2.2
ATM-EoA-IPoE
).
4.4.2.8 ETH-Bridge
If you want to adopt the
Bridge
service and you need to use an
ETH
Interface, follow the steps
below to add a WAN service over a selected ETH interface:
1.
Add a new
ETH
interface on the screen of
4.4.1.2
ETH interface
.
2.
Click the
Add
button on the screen Figure 4-7 and the next configuration is similar to
Bridge
over ATM interface
(see section
4.4.2.3
ATM-EoA-Bridg
).
)
Note:
For ETH-PPPoE, ETH-IPoE and ETH-Bridge, the Bridging option will display in the screen of
Figure 4-20 only when VLAN MUX Mode is selected for Connection Mode
on the screen of Figure
4-5. You have to set the
802.1P Priority
and
802.1Q VLAN ID
.
31
Page 39 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-20
4.4.3 LAN
Choose “
Advanced Setup
”
Æ
“
LAN
”, and you will see the LAN screen (shown in Figure 4-21), the
section allows you to configure the Router’s LAN ports settings.
32
Page 40 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-21
¾
IP Address:
You can configure the Router’s IP Address and Subnet Mask for LAN Interface.
•
IP Address:
Enter the Router’s local IP Address, then you can access to the Web-based
Utility via the IP Address, the default value is 192.168.1.1.
•
Subnet Mask:
Enter the Router’s Subnet Mask, the default value is 255.255.255.0.
¾
Enable IGMP Snooping:
If you select the option, please choose the IGMP Mode
:
Standard
Mode or Blocking Mode.
¾
DHCP Server:
These settings allow you to configure the Router‘s Dynamic Host
Configuration Protocol (DHCP) server function. The DHCP server is enabled by default for the
Router’s Ethernet LAN interface. DHCP service will supply IP settings to computers which are
configured to automatically obtain IP settings that are connected to the Router though the
Ethernet port. When the Router is set for DHCP, it becomes the default gateway for DHCP
client connected to it. Keep in mind that if you change the IP address of the Router, you must
change the range of IP addresses in the pool used for DHCP on the LAN.
33

Rate

4.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top