1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W8960Nv1.3.6
    5. /
  5. 12
Page 56 / 122 Scroll up to view Page 51 - 55
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-43
Click the
Add
button in Figure 4-43, and you can configure the QoS queue entry on the next
screen as shown in Figure 4-44.
Figure 4-44
¾
Name
: Set a name for the entry.
¾
Enable
: Select Enable option to take this entry effect.
¾
Interface
: Assigned a specific Wan Service for this QoS queue entry.
¾
Precedence
: Specify precedence for this QoS queue entry.
¾
DSL Latency
: Select latency path for the type of data transmission, only Path0 is available for
this Router.
After you specify the condition, click
Save/Apply
to save the entry and then you will see you
settings as shown in Figure 4-43.
49
Page 57 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
)
Note:
1)
Lower integer values for precedence imply higher priority for this queue relative to others.
2)
The queue entry configured here will be used by the classifier to place ingress packets
appropriately.
4.4.8.2 QoS Classification
This section will guide you to create a traffic class rule to classify the upstream traffic, assign
queue which defines the precedence and the interface and optionally overwrite the IP header
DSCP byte.
A rule consists of a class name and at least one condition below. All of the specified conditions in
this classification rule must be satisfied for the rule to take effect.
Figure 4-45
Click the
Add
button Figure 4-45, and you can configure the QoS on the next screen.
50
Page 58 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-46
After you specify the condition, click
Save/Apply
to save the entry.
4.4.9 Traffic Control
Choose “
Advanced Setup
”
Æ
“
Traffic Control
” and then you will see the screen as shown in
Figure 4-47. This page allows you to enable this function and to configure the value of
Egress/Ingress Total Rate.
Figure 4-47
51
Page 59 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
¾
Enable
: Check this box to enable the Traffic Control function.
¾
Egress Total Rate (Kbps)
: Enter the upload speed through the WAN port.
¾
Ingress Total Rate (Kbps)
: Enter the download speed through the WAN port.
¾
Line Rate-Upstream (Kbps)
: This field displays the upload speed assigned by your ISP.
¾
Line Rate-Downstream (Kbps)
: This field displays the download speed assigned by your
ISP.
¾
Save/Apply
: Click this button to make the configuration take effect.
)
Note:
1)
The Egress Total Rate and Ingress Total Rate are required to be configured. Otherwise TC
rules cannot be added.
2)
Only when the Router is configured to work in DSL connection does the Line Rate field
display the upload/download speed assigned by your ISP. Otherwise there will be empty.
4.4.9.1 Traffic Control Rule
Choose “
Advanced Setup
”
Æ
“
Traffic Control
”
Æ
“
Traffic Control Rule
” and then you will see the
screen as shown in Figure 4-48. This page allows you to view and configure TC rules.
Figure 4-48
To add a TC rule, click the
Add
button and you can configure it in the screen as shown in Figure
4-49.
52
Page 60 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-49
¾
Rule Status
: Select the status of the rule from the drop-down list to enable or disable the rule.
¾
IP Range
: Enter a single IP address or a range of IP addresses.
¾
Port Range
: Enter a single port or a range of ports.
¾
Protocol
: Select a protocol type from the drop-down list. TCP, UDP and ALL are available
here.
¾
Precedence
: Select precedence form the drop-down list. There are five options: Highest,
High, Medium, Low and Lowest. The default precedence of the rule is Medium.
¾
Egress Rate
: Enter the min and max upload speed through the WAN port.
¾
Ingress Rate
: Enter the min and max download speed through the WAN port.
After completing the above configuration, click the
Save/Apply
button to make it take effect and
then you will see the following list as shown in Figure 4-50. If you want to modify the rule, click the
Edit
button. If you want to delete the rule, check the
Remove
box first and then click the
Remove
button.
Figure 4-50
)
Note:
The precedence, max egress/ingress rate and min egress/ingress rate work on allocation of
surplus upload/download bandwidth. For rules with different precedence, the surplus bandwidth is
firstly allocated to the rule with the highest precedence according to its max egress/ingress rate. If
53

Rate

4.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top