TD-W8960N

300Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 3-11

)

Note:

All the existed

ATM

&

WAN

service will be cleared after clicking the

Save

button on this Quick

Setup page.

5.

You will see the

Finish

screen below, click

Reboot

to save these settings.

Figure 3-12

6.

Now, your ADSL Modem Router has been configured and is rebooting. Please do not power

off the Router while it’s rebooting.

14

TD-W8960N

300Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 3-13

7.

You will see the current configuration has been added to Layer2 Interface list (

4.4.1

Layer2

Interface

) shown in Figure 3-14 and WAN Service list

(4.4.2

WAN Service

)

shown in Figure

3-15.

Figure 3-14

Figure 3-15

)

Note:

More detailed configurations please refer to

4.4.1

Layer2 Interface

and

4.4.2

WAN Service

.

15

TD-W8960N

300Mbps Wireless N ADSL2+ Modem Router User Guide

Chapter 4. Configuring the Router

This chapter will show each Web page's key function and the configuration way.

4.1 Login

After your successful login, you will see the six main menus on the left of the Web-based utility. On

the right, there are the corresponding explanations and instructions.

The detailed explanations for each Web page’s key function are listed below.

4.2 Device Info

Choose “

Device Info

” menu, there are six submenus under the main menu:

Summary

,

WAN

,

Statistics

,

Route

,

ARP

and

DHCP

. This Device Info section mainly introduces the elementary

information about the Router and its current settings in use. Click any of them, and you will be able

to view the corresponding information.

Choose “

Device Info

”

Æ

“

Summary

”, you will see the Summary screen (shown in Figure 4-1). The

first table indicates the information about the version including Software and Hardware. The

second table displays the current status of the TD-W8960N connection. This information will vary

depending on the settings of the Router configured on the Advanced Setup screen.

16

TD-W8960N

300Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 4-1

)

Note:

Click the other submenus under the main menu

Device Info

, and you will be able to view the

corresponding information about

WAN

,

Statistics

,

Route

,

ARP

and

DHCP

.

4.3 Quick Setup

Please refer to Section

3.2 Quick Installation Guide

.

4.4 Advanced Setup

Choose “

Advanced Setup

”, there are many submenus under the main menu. Among the

submenus,

Layer2 Interface

,

WAN Service

,

LAN

etc. are default menus, while

NAT

,

IP/MAC

filtering

of the

Security

,

Quality of Service

and

DNS

will appear only when you select some

corresponding functions. Click any one of them, and you will be able to configure the

corresponding function.

17

TD-W8960N

300Mbps Wireless N ADSL2+ Modem Router User Guide

This Advanced Setup section mainly introduces how to configure the Router for adequate use.

The detailed explanations for each subsection are provided below.

)

Note:

To completely configure the WAN Interface, you need to first select the Layer2 Interface (

4.4.1

Layer2 Interface

) according to the connection ISP provides you, and then to select the type of the

connection (

4.4.2

WAN Service

) for the further configuration.

4.4.1 Layer2 Interface

Choose “

Advanced Setup

”

Æ

“

Layer2 Interface

”, and you can select WAN Service Interface

(layer2 interface) over

ATM interfaces

or

ETH interface

.

¾

ATM Interface:

Configure the Router to access Internet as an ADSL user. ISP provides you

VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings and the DSL Interface

with RJ11 connector. (Figure 2-1)

¾

ETH Interface:

Configure the Router to access Internet as an Ethernet user. ISP provides

you Broadband Internet Service and the Ethernet Interface with RJ45 connector.

4.4.1.1 ATM interface

Choose “

Advanced Setup

”

Æ

“

Layer2 Interface

Æ

ATM interface

”, you can Configure ATM

interfaces on the screen below.

18