Page 26 / 122
Scroll up to view Page 21 - 25
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-2
¾
Remove
: Select the check box in the table on the screen above and then click the
Remove
button, the corresponding interface will be deleted in the table.
)
Note:
If the interface is used by the configuration of the
4.4.2
WAN Service
, you need to remove the
corresponding WAN Service entry first before you can remove it here.
¾
Add
: Click the button, and you can add a new interface in the next screen.
19
Page 27 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-3
¾
VPI
/
VCI
: the VPI and VCI values provided by your ISP. Do not change them unless it was
required by your ISP.
¾
DSL Link Type
: Select a DSL Link Type which is provided by your ISP. The options include
EoA
(it
is for PPPoE, IPoE, and Bridge),
PPPoA
(PPP over ATM) and
IPoA
(IP over ATM).
¾
Encapsulation Mode
: The mode of the data processing over the Link Type you have
selected. Uses the default setting, if you are not sure.
¾
Service Category
: Select the type of the service assigned by your ISP in the drop-down list.
The default type is
UBR Without PCR
.
¾
Connection Mode
: Select the connection mode for
EoA
option of DSL Link Type. The
options include Default mode for single service over one connection, VLAN MUX Mode for
multiple Vlan service over one connection, and MSC Mode for Multiple Service over one
connection.
¾
Enable Quality of Service
: If you want to adopt
QoS
(Quality of Service) for the connection,
please select check box.
)
Note:
Enabling packet level QoS for PVC improves performance for selected classes of applications.
While QoS consumes system resources; therefore the number of PVC(s) will be reduced. Besides
20
Page 28 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
this, it cannot be set for the connection type of CBR and Real-time VBR. If you select the QoS
service, the Quality of Service menu will be added to the Web-based Utility, the detailed
configuration will be described in
4.4.8 Quality of Service
.
4.4.1.2 ETH interface
Choose “
Advanced Setup
”
Æ
“
Layer2 Interface
Æ
ETH Interface
”, you can configure ETH WAN
interfaces on the screen below.
Figure 4-4
)
Note:
To make sure the ETH port available, you should first choose “
Advanced Setup
”
Æ
“
LAN Ports
” to
enable the Virtual LAN Ports feature.
¾
Add:
Click the
Add
button, and you can add a new interface in the next screen.
Figure 4-5
¾
ETH port
: Select an ETH port to configure as the WAN port.
¾
Select Connection Mode
: Choose a connection mode for the port.
Click
Apply/Save
to save your settings and then you will see the screen similar to Figure 4-6.
21
Page 29 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-6
¾
Remove:
Select the check box in the table on the screen above and then click the
Remove
button, the corresponding interface will be deleted in the table.
)
Note:
One ETH is allowed to configure as the layer 2 WAN Interface.
4.4.2 WAN Service
Choose “
Advanced Setup
”
Æ
“
WAN Service
”, and you will see the WAN Port Information Table in
the screen similar to Figure 4-7, which describes the WAN port settings and the relevant
manipulation to each interface. After you add a new Lay2 Interface, please follow the instructions
below to complete the further configuration of WAN Interface. There are five different
configurations for the connection types, which are PPPoE, IPoE, Bridge, PPPoA, and IPoA. You
can select the corresponding types according to your needs.
Figure 4-7
22
Page 30 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
)
Note:
1) The following section adopts different VPI, VCI to introduce further configuration for the
different connection types, if you need to change the configuration of ATM PVC (VPI/VCI), you
should go to the previous section (
4.4.1
Layer2 Interface
) to configure them again.
2) ETH and ATM service can not coexist. If the ETH Interface had configured, you cannot
configure any other WAN service over the ATM Interface until the ETH Interface is deleted.
4.4.2.1 ATM-EoA-PPPoE
If your ISP provides a
PPPoE
connection and you need to use an ATM Interface, follow the steps
below to add a WAN service over a selected ATM interface:
1.
Add a
new
ATM interface and select
EoA
option for DSL Link Type (
4.4.1.1
ATM interface
).
2.
Click the
Add
button on the screen Figure 4-7 and you will enter the next screen as shown in
Figure 4-8. Click
Next
.
Figure 4-8
3.
Select the
WAN service type
in Figure 4-9. If your ISP provides a PPPoE connection, select
PPPoE
option. You can create a service name for the
Service Description
or leave it the
default name. Click
Next
.
Figure 4-9
23
19216811.live