Page 21 / 122
Scroll up to view Page 16 - 20
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 3-11
)
Note:
All the existed
ATM
&
WAN
service will be cleared after clicking the
Save
button on this Quick
Setup page.
5.
You will see the
Finish
screen below, click
Reboot
to save these settings.
Figure 3-12
6.
Now, your ADSL Modem Router has been configured and is rebooting. Please do not power
off the Router while it’s rebooting.
14
Page 22 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 3-13
7.
You will see the current configuration has been added to Layer2 Interface list (
4.4.1
Layer2
Interface
) shown in Figure 3-14 and WAN Service list
(4.4.2
WAN Service
)
shown in Figure
3-15.
Figure 3-14
Figure 3-15
)
Note:
More detailed configurations please refer to
4.4.1
Layer2 Interface
and
4.4.2
WAN Service
.
15
Page 23 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Chapter 4. Configuring the Router
This chapter will show each Web page's key function and the configuration way.
4.1 Login
After your successful login, you will see the six main menus on the left of the Web-based utility. On
the right, there are the corresponding explanations and instructions.
The detailed explanations for each Web page’s key function are listed below.
4.2 Device Info
Choose “
Device Info
” menu, there are six submenus under the main menu:
Summary
,
WAN
,
Statistics
,
Route
,
ARP
and
DHCP
. This Device Info section mainly introduces the elementary
information about the Router and its current settings in use. Click any of them, and you will be able
to view the corresponding information.
Choose “
Device Info
”
Æ
“
Summary
”, you will see the Summary screen (shown in Figure 4-1). The
first table indicates the information about the version including Software and Hardware. The
second table displays the current status of the TD-W8960N connection. This information will vary
depending on the settings of the Router configured on the Advanced Setup screen.
16
Page 24 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-1
)
Note:
Click the other submenus under the main menu
Device Info
, and you will be able to view the
corresponding information about
WAN
,
Statistics
,
Route
,
ARP
and
DHCP
.
4.3 Quick Setup
Please refer to Section
3.2 Quick Installation Guide
.
4.4 Advanced Setup
Choose “
Advanced Setup
”, there are many submenus under the main menu. Among the
submenus,
Layer2 Interface
,
WAN Service
,
LAN
etc. are default menus, while
NAT
,
IP/MAC
filtering
of the
Security
,
Quality of Service
and
DNS
will appear only when you select some
corresponding functions. Click any one of them, and you will be able to configure the
corresponding function.
17
Page 25 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
This Advanced Setup section mainly introduces how to configure the Router for adequate use.
The detailed explanations for each subsection are provided below.
)
Note:
To completely configure the WAN Interface, you need to first select the Layer2 Interface (
4.4.1
Layer2 Interface
) according to the connection ISP provides you, and then to select the type of the
connection (
4.4.2
WAN Service
) for the further configuration.
4.4.1 Layer2 Interface
Choose “
Advanced Setup
”
Æ
“
Layer2 Interface
”, and you can select WAN Service Interface
(layer2 interface) over
ATM interfaces
or
ETH interface
.
¾
ATM Interface:
Configure the Router to access Internet as an ADSL user. ISP provides you
VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings and the DSL Interface
with RJ11 connector. (Figure 2-1)
¾
ETH Interface:
Configure the Router to access Internet as an Ethernet user. ISP provides
you Broadband Internet Service and the Ethernet Interface with RJ45 connector.
4.4.1.1 ATM interface
Choose “
Advanced Setup
”
Æ
“
Layer2 Interface
Æ
ATM interface
”, you can Configure ATM
interfaces on the screen below.
18
19216811.live