1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W8960N
    5. /
  5. 13
Page 61 / 122 Scroll up to view Page 56 - 60
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
there still has surplus bandwidth, it is allocated to the rule with hypo-high precedence. For rules
with the same precedence, the surplus bandwidth is allocated to them according to their min
egress/ingress rate. The greater a rule’s min egress/ingress rate is, the more bandwidth it gets.
4.4.10 Routing
Choose “
Advanced Setup
”
Æ
“
Routing
”, it includes three menus
: Default Gateway
,
Static Route
and RIP
(shown in
Figure 4-51). The detailed descriptions are provided below.
Figure 4-51
4.4.10.1 Default Gateway
Choose “
Advanced Setup
”
Æ
“
Routing
”
Æ
“
Default Gateway
”, you can see the Default Gateway
screen. Deselect the checkbox before
Auto Gateway
, and then you will be able to select a WAN
Interface from the drop-down list as the system default gateway. The
Auto Gateway
checkbox is
selected by default.
Figure 4-52
54
Page 62 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
)
Note:
1)
If changing the Automatic Assigned Default Gateway from unselected to selected, you have
to reboot the Router to get the automatically assigned default gateway.
2) Default Gateway IP address should be specified since MER Interface is selected when you
select the
Enable automatic Assigned Default Gateway
check box.
4.4.10.2 Static Route
Choose “
Advanced Setup
”
Æ
“
Routing
”
Æ
“
Static Route
”. You can see the Static Route screen,
this screen allows you to configure the static routes (shown in Figure 4-53). A static route is a
pre-determined path that network information must travel to reach a specific host or network.
Figure 4-53
To add static routing entries:
1.
Click the
Add
button in Figure 4-53, and you will see the screen as shown in Figure 4-54.
Figure 4-54
2.
Enter the following data:
¾
Destination Network Address:
The
Destination Network Address
is the address of the
network or host that you want to assign to a static route.
¾
Subnet Mask:
The
Subnet Mask
determines which portion of an IP Address is the network
portion, and which portion is the host portion.
55
Page 63 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
¾
Use Interface:
Select the Interface name in the text box, or else, the default Use Interface will
be adopted for the Static Route.
¾
Use Gateway IP Address:
If you select the IPoE or IPoA mode for
Use Interface
, the
screen above will display this item, you should type the Gateway address correctly, and the
other option for
Use Interface
will adopt the default Gateway address for the Static Route.
3.
Click
Save/Apply
to and then you will see you settings as shown in Figure 4-53.
To remove a static routing entry:
1.
Select the
Remove
check box according to the entry in the Figure 4-53.
2.
Click the
Remove
button, and the entry will be deleted.
)
Note:
Gateway IP address should be correctly configure
d if IP based Interface (IPoE, IPoA) i
s selected.
4.4.10.3 RIP
Choose “
Advanced Setup
”
Æ
“
Routing
”
Æ
“
RIP
”, you can see the RIP (Routing Information
Protocol) screen which allows you to configure the RIP (shown in Figure 4-55).
Figure 4-55
)
Note:
RIP cannot be configured on the WAN Interface which has NAT enabled (such as PPPoE).
To activate RIP for the device, configure an individual interface, select the desired RIP version and
operation, and select
Enabled
checkbox for the interface.
Click
Save/Apply
to save the configuration.
56
Page 64 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
4.4.11 DNS
When you select the connection type
PPPoE
,
PPPoA
or
IPoA
for WAN configuration, you will see
the
DNS
menu in the Web-based Utility (shown in Figure 4-56). It includes
DNS Server
and
Dynamic DNS
submenus.
Figure 4-56
4.4.11.1 DNS Server
Choose “
Advanced Setup
”
Æ
“
DNS
”
Æ
“
DNS Server
”, and you can see the
DNS Server
Configuration
screen. Deselect the checkbox before
Auto DNS Server
, and then you will be able
to manually configure the DNS Server Addresses as shown in Figure 4-57.
Figure 4-57
For PPPoA, PPPoE enabled PVC(s), please select the
Obtain DNS info from a WAN interface
checkbox, this Router will accept automatically the first received DNS assignment from the
selected configured WAN interface during the connection establishment.
57
Page 65 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
For single PVC with IPoA, static IPoE protocol, please select the
Use the following Static DNS IP
address
checkbox, and enter the primary and /or optional secondary DNS server IP addresses
provided by your ISP.
Click the
Apply/Save
button to save the new configuration.
4.4.11.2 Dynamic DNS
Choose “
Advanced Setup
”
Æ
“
DNS
”
Æ
“
Dynamic DNS
”, you can see the
Dynamic DNS
screen,
this screen allows you to configure the Dynamic DNS (shown in Figure 4-58).
The Router offers a Dynamic Domain Name System (
DDNS
) feature. DDNS lets you assign a
fixed host and domain name to a dynamic Internet IP Address. The Dynamic DNS service allows
you to alias a dynamic IP address to a static hostname in any of the many domains, allowing your
Router to be more easily accessed from various locations on the Internet.
Figure 4-58
To add a DDNS entry:
1.
Click the
Add
button (pop-up Figure 4-58), and then you will set the DDNS in the next screen
(shown in Figure 4-59).
58

Rate

4 / 5 based on 1 vote.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top