Page 26 / 63
Scroll up to view Page 21 - 25
TD-8840
ADSL2+ Modem Router User Guide
20
Figure 3-23
b)
Click
Save/Reboot
.
Figure 3-24
)
Note:
After you complete any setup, the new setup must be saved and the Router must be restarted for
the configuration to take effect. Please click the
Save/Reboot
button to restart.
Page 27 / 63
TD-8840
ADSL2+ Modem Router User Guide
21
Chapter 4. Software Configuration
This User Guide recommends using the “Quick Installation Guide” for first-time installation. For
advanced users, if you want to know more about this device and make use of its functions
adequately, maybe you will get help from this chapter to configure the advanced settings through
the Web-based Utility. After your successful login, you can configure and manage the device.
4.1
Device Info
The Device Info page provides the current information about the ADSL 2+ Modem Router. All
information is read-only.
Figure 4-1
4.2
Quick Setup
Please refer to
3.3 Quick Setup
.
4.3
Advanced Setup
Choose “
Advanced Setup
”, and you can see the submenus as shown in Figure 4-2.
Figure 4-2
Page 28 / 63
TD-8840
ADSL2+ Modem Router User Guide
22
4.3.1 WAN
Choose “
Advanced Setup
”
Æ
”
WAN
”, and you will see the page of Wide Area Network (WAN)
Setup as shown in Figure 4-3.
Figure 4-3
There are 4 PVC links in the
WAN
setup page. Click the
Add
button or choose the appropriate
PVC according to your need. Then you will enter the page of
ATM PVC Configuration
as shown
in Figure 4-4.
Figure 4-4
Enter
VPI/VCI
value and service category provided by your ISP. Click
Next
to enter the next step.
You will see the Figure 4-5.
Page 29 / 63
TD-8840
ADSL2+ Modem Router User Guide
23
Figure 4-5
After choosing the proper protocol, enter the correct parameters supported by your ISP. Enable
the configurations, and then you will go to the Internet.
)
Note:
The type of network protocol selected may be different in different areas. There are five types
（
Figure 4-5
）
, so you should ask your ISP to acquire the
Connection Type
and
Encapsulation
Mode
.
¾
PPP over ATM (PPPoA)
If you select the protocol of PPP over ATM (PPPoA), you will see the Figure 4-6.
Page 30 / 63
TD-8840
ADSL2+ Modem Router User Guide
24
Figure 4-6
¾
PPP Username:
Enter your username for your PPPoA connection to identify and verify your
account to the ISP.
¾
PPP Password:
Enter your password for your PPPoA connection.
¾
Authentication Method:
Choose a method of authentication,
AUTO
,
PAP
,
CHAP
, or
MSCHAP
.
¾
MTU:
The default
MTU
value is 1480 Bytes. It is not recommended that you change the
default value unless required by your ISP. The value should be between 512 and 1500.
¾
Dial on demand:
If you check this box, the Internet connection can be terminated
automatically after a specified inactivity period (
Inactivity Timeout
) and be re-established
when you attempt to access the Internet again. The default value of
Inactivity Timeout
is 15.
The value should be between 1 and 4320.
¾
PPP IP extension:
If this box is checked, the IP address obtained by the Router will be
assigned to the computer, and the NAT and Firewall will be disabled.
¾
Use Static IP Address:
Check this box to use the static IP address to dial. The default value
is disabled.
¾
Enable PPP Debug Mode:
Check this box to enable the debug mode. The default value is
disabled.
19216811.live