1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. Archer D9
    5. /
  5. 7
Page 31 / 125 Scroll up to view Page 26 - 30
Archer
D9
AC1900 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
Figure 4-4
4.5.1.1 Static IP
Select this option if your ISP provides static IP information to you. You should set static IP address,
IP subnet mask, and gateway address in the screen below.
20
Page 32 / 125
Archer
D9
AC1900 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
Figure 4-5
ATM Configuration:
VPI (0~255):
Identifies the virtual path between endpoints in an ATM network. The valid range
is from 0 to 255. Please input the value provided by your ISP.
VCI (1~65535):
Identifies the virtual channel endpoints in an ATM network. The valid range is
from 1 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value
provided by your ISP.
Click
Advance
, the advanced selections of ATM Configuration can be shown.
Encapsulation Mode:
Select the encapsulation mode for the Static IP Address. Here you
can leave it by default.
ATM Qos Type:
Select ATM Qos Type provided by your ISP. The default type is UBR.
WAN Service Setup:
Enable IPv4
：
Check the box to enable IPv4.
IP Address:
Enter the IP address in dotted-decimal notation provided by your ISP.
Subnet Mask:
Enter the subnet Mask provided by your ISP, which is usually 255.255.255.0.
21
Page 33 / 125
Archer
D9
AC1900 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
Gateway
(Optional): Enter the gateway IP address in dotted-decimal notation provided by
your ISP.
DNS Server/ Secondary DNS Server:
Here you can set DNS Server (at least one) manually.
The modem router will use the first DNS Server for priority.
Default Gateway:
Select a WAN Interface from the drop-down list as the IPv4 default
gateway.
Enable IPv6:
Check the box to enable IPv6.
IPv6 Address:
Enter the IPv6 address provided by your ISP.
Prefix Length:
Enter the prefix length of the IPv6 address. The default value is 64.
IPv6 Gateway:
Enter the gateway IPv6 address provided by your ISP.
IPv6 DNS Server / Secondary IPv6 DNS Server:
Here you can set IPv6 DNS Server (at
least one) manually. The Route will use this IPv6 DNS Server for priority.
IPv6 Default Gateway:
Select a WAN Interface from the drop-down list as the IPv6 default
gateway.
Click
Advance
, advanced selections of WAN Service Setup can be shown.
MTU (bytes)
: The default
MTU
(Maximum Transmission Unit) value is 1500 Bytes. Do not
change the default value unless required by your ISP.
Enable NAT
: This technology translates the IP addresses of a local area network to a
different IP address for the Internet. If this modem router is hosting your network’s connection
to the Internet, please select the check box.
Enable Fullcone NAT
: It is a type of NAT, if not enabled, the default NAT will act.
Enable SPI Firewal
l: The SPI firewall enhances network’s security. Select the option to use a
firewall, or else without a firewall.
Enable IGMP Proxy
: IGMP (Internet Group Management Protocol) is used to manage
multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for
client devices, such as the modem router. It is enabled by default.
Click the
Save
button to save the settings.
4.5.1.2 Dynamic IP
Select
Dynamic IP
type if your ISP provides the DHCP service, and the modem router will
automatically get IP parameters from your ISP.
22
Page 34 / 125
Archer
D9
AC1900 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
Figure 4-6
Click
Advance
, advanced selections for WAN Service Setup can be shown.
MTU (bytes):
The default
MTU
(Maximum Transmission Unit) value is 1500 Bytes. Do not
change the default value unless required by your ISP.
Enable NAT:
This technology translates the IP addresses of a local area network to a different
IP address for the Internet. If this modem router is hosting your network’s connection to the
Internet, please select the check box.
Enable Fullcone NAT
: It is a type of NAT, if not enabled, the default NAT will act.
Enable SPI Firewall:
The
SPI firewall enhances network’s security. Select the option to use a
firewall, or else without a firewall.
Enable
IGMP Proxy
: IGMP (Internet Group Management Protocol) is used to manage
multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for
client devices, such as the modem router. It is enabled by default.
Get IP with Unicast:
It is disabled
by default. A few ISPs’ DHCP Servers do not support the
broadcast applications. When the modem router cannot get the IP address normally, you can
choose this option. (It is rarely required)
Set DNS Server manually:
Choose
“Set DNS Server manually”, you can set DNS Server
manually here. The modem router will use this DNS Server for priority.
Get IPv6 Address with Unicast:
It is disabled
by default. A few ISPs’ DHCP Servers do not
support the broadcast applications. When the modem router cannot get the IPv6 address
normally, you can choose this option. (It is rarely required.)
23
Page 35 / 125
Archer
D9
AC1900 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
Set IPv6 DNS Server manually:
Choose
“Set IPv6 DNS Server manually”, you can set IPv6
DNS Server manually here. The modem router will use this IPv6 DNS Server for priority.
Host Name:
Here displays model number of your modem router.
Click the
Save
button to save the settings.
4.5.1.3 PPPoE
If your ISP provides a
PPPoE
connection and you need to use an ATM Interface, choose
PPPoE
in the drop-down list, and then the screen will be displayed as below.
Figure 4-7
PPP Username/Password/Confirm Password
: Enter the User Name and Password
provided by your ISP. These fields are case-sensitive.
Always on:
The connection can be re-established automatically when it is down.
24

Rate

3.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top