1. Home
    2. /
  2. Manuals
    3. /
  3. Tenda
    4. /
  4. D301
    5. /
  5. 7
Page 31 / 103 Scroll up to view Page 26 - 30
Wireless Modem Router User Guide
- 31 -
PPP User Name:
This is for logging in to your ISP.
If you cannot locate this information, ask your ISP to provide
it.
PPP Password:
This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.
Authentication Method:
This is used by ISP to authenticate the client that attempts to connect. If you are not sure,
consult your ISP or select
Auto
.
Dial on demand:
Connect to ISP only when there is traffic transmission. This saves your broadband Internet
service bill.
Enable PPP Debug Mode:
Only enable this feature if supported by your ISP.
Bridge PPPoE Frames Between WAN and Local Ports:
If enabled, PPPoE dialup frame from LAN side will
directly egress the WAN port without modification.
Multicast Proxy:
If enabled, the router will use multicast proxy.
If you are not sure about the options on this screen, simply enter your ISP user name and password and leave the other
options unchanged from defaults. Click
Next
to enter the following screen.
WAN gateway
Here you can configure the WAN gateway address. After you configure it click
Next
. The default setting is
recommended.
_________________________________________________________________________________________________
Note:
Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be
used according to the priority with the first being the higest and the last one the lowest priority if the WAN interface is
connected.
Priority
order
can
be
changed
by
removing
all
and
adding
them
back
in
again.
_________________________________________________________________________________________________
Page 32 / 103
Wireless Modem Router User Guide
- 32 -
WAN DNS
Here you can configure the WAN DNS address:
-Click the
Select DNS Server Interface from available WAN interfaces
option
-OR select the
Use the following Static DNS IP address
option and enter static DNS server IP addresses for the system
And then click
Next
.
_________________________________________________________________________________________________
Note:
1. DNS Server Interfaces can have multiple WAN interfaces served as system dns servers but only one will be used
according to the priority with the first being the higest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
2. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses
must be entered.
3. If you cannot locate the static DNS server IP information, ask your ISP to provide it.
_________________________________________________________________________________________________
Here you can view your configurations. Click
Apply/Save
to save your settings if everything is correctly set.
Page 33 / 103
Wireless Modem Router User Guide
- 33 -
When the PPPoA connection is successful, you can access Internet.
IPoA
If you have selected the
IPoA
from the
ATM Interface
screen in
Layer2 Interface
, you will see the screen above when
you click the
WAN Service
tab, select the configured interface and click
Next
.
1.
Edit the
Enter Service Description.
This field is optional. We recommend that you keep the default.
2.
Click
Next.
Page 34 / 103
Wireless Modem Router User Guide
- 34 -
WAN IP Address:
The Internet IP address provided by your ISP for accessing Internet.
WAN Subnet Mask:
The subnet mask address provided by your ISP for accessing Internet.
Enter the WAN IP address and subnet mask assigned by your ISP. This information should have been provided to you by
your ISP. If you cannot locate this information, ask your ISP to provide it. And then click
Next
to enter the following
screen.
If you are unsure about the options on the screen above, keep the defaults and click
Next
.
Here you can configure the WAN gateway address. After you configure it click
Next
. The default setting is
recommended.
______________________________________________________________________________________________
Note:
Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be
used according to the priority with the first being the higest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
______________________________________________________________________________________________
Here you can configure the WAN DNS address:
-Click the
Select DNS Server Interface from available WAN interfaces
option
-OR select the
Use the following Static DNS IP address
option and enter static DNS server IP addresses for the system
Page 35 / 103
Wireless Modem Router User Guide
- 35 -
And then click
Next
to enter the following screen.
_________________________________________________________________________________________________
Note:
1. DNS Server Interfaces can have multiple WAN interfaces served as system dns servers but only one will be used
according to the priority with the first being the higest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
2. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses
must be entered.
3. If you cannot locate the static DNS server IP information, ask your ISP to provide it.
_________________________________________________________________________________________________
Confirm your settings and then click Apply/Save to apply and save your settings. Your settings will then be displayed on
the screen below:
To setup WAN Service for ETH Interface
If you select and configured the
ETH Interface
(Ethernet uplink), follow steps below to configure the WAN service:
Two Internet connections: PPP over Ethernet (PPPoE) and IP over Ethernet (IPoE) are available in the Ethernet uplink
mode.
_________________________________________________________________________________________________
Tip:
eth0, eth1, eth3 and eth3 respectively represent the LAN port1, LAN port2, LAN port3 and LAN port4 of the device.
_________________________________________________________________________________________________

Rate

124.8 / 5 based on 304 votes.

Popular Tenda Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top