Tenda D301 Router Manual PDF (Setup & Configuration Guide)

Page 21 / 103 Scroll up to view Page 16 - 20

Wireless Modem Router User Guide

- 21 -

assigns you a static (fixed) IP

address, IP subnet mask and the

gateway IP address, you need to

select the IP over Ethernet (IPoE).

available, enter it also.

IPoA

Static (Fixed) IP

Enter the assigned IP address, subnet mask, and the IP address of

your ISP’s primary DNS server. This information should have been

provided to you by your ISP. If a secondary DNS server address is

available, enter it also.

Bridging

If you wish to iniate a dialup directly from your PC for Internet

access or enjoy the entire Internet connection (instead of sharing it

with others), you can select the

Bridging

and then click

_________________________________________________________________________________________________

Tip:

For PPPoE, IPoE, and Bridging Internet connection types, you must first select EoA on the ATM Interface Screen, for

more information, see

To set up the ATM interface

.

_________________________________________________________________________________________________

PPP over Ethernet (PPPoE)

If you have selected the

EoA

from the

ATM Interface

screen in

Layer2 Interface

, you will see the screen below when

you click the

WAN Service

tab, select the configured interface and click

1.

Select PPPoE.

2.

Edit the

Enter Service Description.

This field is optional. We recommend that you keep the default.

3.

Select a network protocol: IPv4, IPv6 or IPv4 & IPv6 (dual stack).

4.

Click

Next.

_________________________________________________________________________________________________

Note:

If you select IPv6 or IPv4 & IPv6 (dual stack), skip to

IPv6

.

_________________________________________________________________________________________________

Page 22 / 103

Wireless Modem Router User Guide

- 22 -



PPP User Name:

This is for logging in to your ISP.

If you cannot locate this information, ask your ISP to provide

it.



PPP Password:

This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.



PPPoE Service Name:

This information is provided by your ISP. Only enter it if instructed by your ISP.



Authentication Method:

This is used by ISP to authenticate the client that attempts to connect. If you are not sure,

consult your ISP or select

Auto

.



Clone MAC:

Clicking this button copies the MAC address of your PC to the router. Many broadband ISPs restrict

access by allowing traffic only from the MAC address of your broadband modem, but some ISPs additionally

register the MAC address of the network interface card in your computer when your account is first opened. They

then accept traffic only from the MAC address of that computer. If so, configure your router to “clone” the MAC

address from the authorized computer.



Dial on demand:

Connect to ISP only when there is traffic transmission. This saves your broadband Internet

service bill.



PPP IP extension:

If enabled, all the IP addresses in outgoing packets including management packets on the WAN

port will be changed to the device's WAN IP address.

Only change the default settings if necessary.



Enable PPP Debug Mode:

Only enable this feature if supported by your ISP.



Bridge PPPoE Frames Between WAN and Local Ports:

If enabled, PPPoE dialup frame from LAN side will

directly egress the WAN port without modification.



Multicast Proxy:

If enabled, the router will use multicast proxy.

IPv6

If you select IPv4 as the network protocol, skip this section.

Page 23 / 103

Wireless Modem Router User Guide

- 23 -

1.

Check

Launch Dhcp6c for Prefix Delegation (IAPD).

2.

If your ISP is using stateful DHCPv6, check

Launch Dhcp6c for Address Assignment (IANA)

also. Or configure

a static IP address.

3.

Click

Next ->

Next -> Apply/Save.

WAN Gateway

Here you can configure the WAN gateway address. After you configure it click

recommended.

_________________________________________________________________________________________________

Note:

Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be

used according to the priority with the first being the higest and the last one the lowest priority if the WAN interface is

connected. Priority order can be changed by removing all and adding them back in again.

_________________________________________________________________________________________________

WAN DNS

Here you can configure the WAN DNS address:

-Click the

Select DNS Server Interface from available WAN interfaces

option

-OR select the

Use the following Static DNS IP address

option and enter static DNS server IP addresses for the system

And then click

_________________________________________________________________________________________________

Note:

1.DNS Server Interfaces can have multiple WAN interfaces served as system dns servers but only one will be used

according to the priority with the first being the higest and the last one the lowest priority if the WAN interface is

connected. Priority order can be changed by removing all and adding them back in again.

2. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses

Page 24 / 103

Wireless Modem Router User Guide

- 24 -

must be entered.

3. If you cannot locate the static DNS server IP information, ask your ISP to provide it.

_________________________________________________________________________________________________

Here you can view your configurations. Click

Apply/Save

to save your settings if everything is correctly set.

When the PPPoE connection is successful, you can access Internet.

IP over Ethernet (IPoE)

If your ISP uses DHCP to assign your IP address or if your ISP assigns you a static (fixed) IP address, IP subnet mask

and the gateway IP address, you need to select the IP over Ethernet (IPoE).

If you have selected the

EoA

from the

ATM Interface

screen in

Layer2 Interface

, you will see the screen below when

you click the

WAN Service

tab, select the configured interface and click

Page 25 / 103

Wireless Modem Router User Guide

- 25 -

1.

Select IPoE.

2.

Edit the

Enter Service Description.

This field is optional. We recommend that you keep the default.

3.

Select a network protocol: IPv4, IPv6 or IPv4 & IPv6 (dual stack).

4.

Click

Next.

_________________________________________________________________________________________________

Note:

If you select IPv6 or IPv4 & IPv6 (dual stack), skip to

IPv6

.

_________________________________________________________________________________________________



Obtain an IP address automatically:

This allows the router to automatically acquire IP information from your ISP

or your existing networking equipment.



Use the following Static IP address:

This allows you to specify the Static IP information provided by your ISP or

that corresponds with your existing networking equipment.



WAN IP Address:

The Internet IP address provided by your ISP for accessing Internet.



WAN Subnet Mask:

The subnet mask address provided by your ISP for accessing Internet.



WAN gateway IP Address:

The gateway IP address provided by your ISP for accessing Internet.

Rate

Popular Tenda Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share