Page 26 / 103
Scroll up to view Page 21 - 25
Wireless Modem Router User Guide
- 26 -
IPv6
If you select IPv4 as the network protocol, skip this section.
To obtain an IP address automatically:
1.
Select
Obtain an IP address automatically.
2.
Check
Launch Dhcp6c for Prefix Delegation (IAPD).
3.
If your ISP is using stateful DHCPv6, check
Launch Dhcp6c for Address Assignment (IANA)
also.
4.
Click
Next ->
Next -> Apply/Save.
To configure a static IPv6 address
1.
Select
Use the following Static IPv6 address.
2.
Configure
WAN IPv6 Address/Prefix Length
and
WAN Next-Hop IPv6 Address.
3.
Click
Next ->
Next
to enter the screen below.
Page 27 / 103
Wireless Modem Router User Guide
- 27 -
4.
Select
Use the following Static IPv6 DNS address
and manually enter the DNS server address. If you have two
DNS server addresses, enter the second also.
5.
Click
Next -> Apply/Save
.
_________________________________________________________________________________________________
Note:
If "Obtain an IP address automatically" is chosen, DHCP will be enabled for PVC in IPoE mode.
_________________________________________________________________________________________________
Here you can configure the NAT settings. If you are unsure about the options, please keep the default settings and then
click
Next
.
Here you can configure the WAN gateway address. Default gateway interface list can have multiple WAN interfaces
served as system default gateways but only one will be used according to the priority with the first being the higest and
the last one the lowest priority if the WAN interface is connected. Priority order can be changed by removing all and
Page 28 / 103
Wireless Modem Router User Guide
- 28 -
adding them back in again.
If you are unsure about the options, please keep the default settings and then click
Next
.
Here you can configure the WAN DNS address:
-Click the
Select DNS Server Interface from available WAN interfaces
option
-OR select the
Use the following Static DNS IP address
option and enter static DNS server IP addresses for the system
And then click
Next
.
_________________________________________________________________________________________________
Note:
1. DNS Server Interfaces can have multiple WAN interfaces served as system dns servers but only one will be used
according to the priority with the first being the higest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
2. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses
must be entered.
3. If you cannot locate the static DNS server IP information, ask your ISP to provide it.
_________________________________________________________________________________________________
Here you can view your configurations. Click
Apply/Save
to save your settings if everything is correctly set.
Page 29 / 103
Wireless Modem Router User Guide
- 29 -
When the IPoE connection is successful, you can access Internet.
Bridging
If you wish to iniate a dialup directly from your PC for Internet access or enjoy the entire Internet connection (instead of
sharing it with others), you can use the Bridging DSL link type and create a dialup program on your PC.
If you have selected the
EoA
from the
ATM Interface
screen in
Layer2 Interface
, you will see the screen below when
you click the
WAN Service
tab, select the configured interface and click
Next
.
The
Enter Service Description
field is optional. We recommend that you keep it unchanged from default and click
Next
.
Page 30 / 103
Wireless Modem Router User Guide
- 30 -
Here you can view your configurations. Click
Apply/Save
to save your settings if everything is correctly set.
When the bridging connection is successful, you can access Internet.
_________________________________________________________________________________________________
Note:
To configure multiple WAN connections, simply configure multiple ATM interfaces and then follow the instructions
above.
_________________________________________________________________________________________________
PPPoA
If you have selected the
PPPoA
from the
ATM Interface
screen in
Layer2 Interface
, you will see the screen below
when you click the
WAN Service
tab, select the configured interface and click
Next
.
1.
Edit the
Enter Service Description.
This field is optional. We recommend that you keep the default.
2.
Select a network protocol: IPv4, IPv6 or IPv4 & IPv6 (dual stack).
3.
Click
Next.
19216811.live