Page 36 / 165 Scroll up to view Page 31 - 35
Telsey
telecommunications
Web Interface
MT500--SIEN12
28
ADVANCED SETUP
WAN
WAN Setup
By clicking on
WAN
in the
Advanced Setup
menu it is possible to begin the
configuration of WAN interfaces. The following screen shows the inital situation,
when no WAN interface is present.
By clicking on
Add
button, it is possible to begin the setup.
ATM PVC Configuration
The first page to configure is
ATM PVC Configration.
These settings are
usually given by Internet Service Providers.
In this page it is possible to set VPI, VCI and Service Category.
Avaliable Service Categories are:
UBR (Unspecified Bit Rate) without PCR (Peak Cell Rate)
UBR with PCR
CBR (Constant Bit Rate)
Non Realtime VBR (Variable Bit Rate)
Realtime VBR
The following figure shows the ATM PVC Configuration Page
Page 37 / 165
Telsey telecommunications
Web Interface
29
MT500--SIEN12
In case of UBR with PCR and CBR, it is possible to set
Peak Cell Rate
[cells/s]
value.
In case of Non Realtime VBR, it is possible to set values for:
Peak Cell Rate [cells/s]
Sustainable Cell Rate [cells/s]
Maximum Burst Size [cells]
Click on Next to set Connection Type.
Connection Type
The
Connection Type
page allows to select the type of encapsulation protocol
and encapsulation mode over the ATM PVC that has been selected in the
previous page.
Avaliable connection types are:
PPP over ATM (PPPoA)
PPP over Ethernet (PPPoE)
MAC Encapsulation Routing (MER)
IP over ATM (IPoA)
Bridging
Depending on the selected network protocol, it is then possible to choose an
appropriate encapsulation mode (VC/MUX, LLC/ENCAPSULATION, LLC/SNAP
BRIDGING, VC/MUX, LLC/SNAP ROUTING).
Page 38 / 165
Telsey
telecommunications
Web Interface
MT500--SIEN12
30
The following figure shows the Connection Type page.
The following table shows all the encapsulation modes avaliable for each
network protocol.
Each Network Protocol needs further configurations, which can be set by
clicking on Next.
PPPoA
If
PPP over ATM
is chosen, regardless of the selected encapsulation mode, the
following screen requires to set PPP Username and Password. The Password
requirement is dependent on the particular requirements of the ISP or ADSL
Service Provider.
PPP Username max. length is 256 characters, PPP Password max. length is 32
characters.
Tab. 7: Network Protocol and Encapsulation Mode
Protocol
Encapsulation Mode
PPP over ATM
VC/MUX, LLC/ENCAPSULATION
PPP over Ethernet
LLC/SNAP BRIDGING, VC/MUX
MAC Encapsulation Routing
LLC/SNAP BRIDGING, VC/MUX
IP over ATM
LLC/SNAP ROUTING, VC/MUX
Bridging
LLC/SNAP BRIDGING, VC/MUX
Page 39 / 165
Telsey telecommunications
Web Interface
31
MT500--SIEN12
The following figure shows PPP Username and Password page.
CPVA500 can be configured to disconnect if there is no activity for a period of
time by selecting the
Disconnect if no activity
box. Default time is 30
minutes.
As
Authentication Method
, either “PAP”, or “CHAP” can be used. If “AUTO”
is selected, then the authentication protocol is automatically selected.
PPP IP extension
is a special feature deployed by some service providers.
Unless your service provider specifically requires this setup, do not select it.
The PPP IP Extension supports the following conditions:
Allows only one PC on the LAN
The public IP address assigned by the remote using the PPP/IPCP protocol
is actually not used on the WAN PPP interface. Instead, it is forwarded to the
PC's LAN interface through DHCP. Only one PC on the LAN can be connected
to the remote since the DHCP server within the ADSL router has only a
single IP address to assign to a LAN device.
NAPT and firewall are disabled when this option is selected.
The ADSL router becomes the default gateway and DNS server to the PC
through DHCP using the LAN interface IP address.
The ADSL router extends the IP subnet at the remote service provider to the
LAN PC. That is, the PC becomes a host belonging to the same IP subnet.
The ADSL router bridges the IP packets between WAN and LAN ports, unless
the packet is addressed to the router's LAN IP address.
By clicking on Next, it is then possible to enable or disable WAN service (and
assign a service name), IGMP multicast (not supported yet) and Quality of
Service. QoS can be activated and then controlled by means of the relative
menu (Advanced Setup --> Quality of Service). Note that enabling QoS for a
Page 40 / 165
Telsey
telecommunications
Web Interface
MT500--SIEN12
32
selected PVC improves performance for selected classes of applications, but
also reduces the number of available PVC’s.
The following figure shows the relative page.
By clicking on Next, the WAN Setup Summary shows up.

Rate

4 / 5 based on 1 vote.

Popular Telsey Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top