Page 136 / 165 Scroll up to view Page 131 - 135
Telsey
telecommunications
Command Line Interface
MT500--SIEN12
128
Valid values: enable or disable. Default value: enable.
--nat <enable|disable>
: the NAT state of the MER or IPoA interface.
Notice that NAT is always enabled on a PPPoE or a PPPoA interface. Valid
values: enable or disable.
Default value: enable.
--username <username>
: the login name of the PPPoE or PPPoA
interface. This option is only applied to a PPPoE or PPPoA interface. The
--password option is also needed when this option is used.
Valid values: string of 32 characters.
--password <password>
: the password of the PPPoE or PPPoA interface.
This option is only applied to a PPPoE or PPPoA interface. The --username
option is also needed when this option is used.
Valid values: string of 256 characters.
--pppidletimeout <timeout>
: the PPP timeout of a PPPoE or PPPoA
interface. This option is only applied to a PPPoE or PPPoA interface. Valid
values: 0 - 1090 (minutes). 0: PPP connection is always-on. Greater than
0: WAN traffic will be monitored and PPP connection will be torn down
when there is no user data activity over the WAN interface for more than
this idle time period.
Default value: 30 minutes.
--pppipextension <disable|enable>
: the PPP IP extension mode of a
PPPoE or PPPoA interface. This option is only applied to a PPPoE or PPPoA
interface. Valid values: disable or enable.
Default value: disable.
--ipaddr <wanipaddress> <wansubnetmask>
: the WAN IP address and
WAN subnet mask of a MER or IPoA interface.
This option should only be used for a MER or IPoA interface. PPPoE and
PPPoA interface always receives the IP address, submask and DNS
addresses automatically from the ISP through the PPP protocol. If this
option is used and the dhcpclient value is "enable", DHCP client will be
disabled on this interface. In general principle, static configuration
overwrites dynamically assigned data.
<wanipaddress>
: the WAN IP address. Valid values: any valid IP
address.
<wansubnetmask>
: the WAN subnet mask. Valid values: 0.0.0.1 -
255.255.255.255.
--dhcpclient <enable|disable>
: the DHCP client state of the MER
interface. This option is only valid to a MER interface. DHCP client is not
supported over any other type of WAN interface.
Valid values: enable or disable.
Default value: enable.
Options for the
delete
command:
wan delete <port.vpi.vci>
port
: port number of the VCC to add. Valid values: 0.
vpi
: VPI of the VCC to add. Valid values: 0 - 255. Default value: 0
vci
: VCI of the VCC to add. Valid values: 32 - 65535. Default value: 35.
Page 137 / 165
Telsey telecommunications
Command Line Interface
129
MT500--SIEN12
Options for the
show
command:
wan show [<port.vpi.vci>]
port
: port number of the VCC to add. Valid values: 0.
vpi
: VPI of the VCC to add. Valid values: 0 - 255. Default value: 0
vci
: VCI of the VCC to add. Valid values: 32 - 65535. Default value: 35
If <port.vpi.vci> is obmitted then it will display summary state of all
existing WAN
interfaces. Notice, configuration needs to be saved to the
Permanent Storage first and then become effective after reboot. The wan
show command shows the WAN interfaces after reboot, the second
stage.
Options for the
--help
command:
wan --help [ < bridge | pppoe | pppoa | mer | ipoa > ]
< bridge |
pppoe | pppoa | mer | ipoa>
Display only valid options for the specified protocol.
If it is obmitted then the help for all protocols is diplayed.
EXAMPLES:
Configure a PPPoE interface
wan config 0.0.35 --protocol pppoe --username username --
password password --encap llc
Configure a PPPoA interface
wan config 0.0.36 --protocol pppoa --username username --
password password --encap vcmux
Configure a MER configuration using DHCP client
wan config 0.0.37 --protocol mer --encap llc
Configure a MER configuration using static WAN address
wan config 0.0.37 --protocol mer --encap llc --ipaddr
10.6.33.163 255.255.255.0
Configure a IPoA configuration without fireware, without NAT
wan config 0.0.40 --protocol ipoa --encap llc --firewall
disable --nat disable --ipaddr 10.6.33.227 255.255.255.0
Configure a bridge configuration
wan config 0.2.35
Remove a WAN interface
wan delete 0.2.35
Display all WAN interfaces
wan show
Page 138 / 165
Telsey
telecommunications
Command Line Interface
MT500--SIEN12
130
Display usage for all protocols
wan --help
Usage: wan config <port.vpi.vci>
[--protocol <bridge|pppoe|pppoa|mer|ipoa>] [--encap
<llc|vcmux>]
[--state <enable|disable>] [--service <servicename>]
[--firewall <enable|disable>] [--nat <enable|disable>]
[--username <username> --password <password>]
[--pppidletimeout
<timeout>]
[--pppipextension
<disable|enable>]
[--ipaddr <wanipaddress> <wansubnetmask]
[--dhcpclient <enable|disable>]
wan delete <port.vpi.vci>
wan show [<port.vpi.vci>]
wan --help <bridge|pppoe|pppoa|mer|ipoa>
Display usage for bridge
wan --help bridge
Usage: wan config <port.vpi.vci>
[--protocol <bridge|pppoe|pppoa|mer|ipoa>] [--encap
<llc|vcmux>]
[--state <enable|disable>] [--service <servicename>]
wan delete <port.vpi.vci>
wan show [<port.vpi.vci>]
wan --help <bridge|pppoe|pppoa|mer|ipoa>
======================================================================
=========
VCC Catego. Service Intf. Proto. State Status IP
Name Name address
======================================================================
=========
0.0.35 UBR pppoe_0_35 ppp33 PPPoE Enable Up 10.6.33.143
0.0.36 UBR pppoa_0_36 ppp42 PPPoA Enable Up 10.6.33.152
0.0.37 UBR mer_0_37 nas27 MER Enable Up 10.6.33.193
0.0.40 UBR ipoa_0_40 atm52 IPoA Enable Up 10.6.33.227
===============================================================================
Page 139 / 165
Telsey telecommunications
Technical Features
131
MT500--SIEN12
Chapter 7
Technical Features
Broadband Interface
ADSL compliant with:
ANSI T1.413 I2
ITU Automode
G.992.2G.Lite
G.992.1 Annex A - G.dmt
Up to 840 Kbps upstream (CPE to CO)
Up to 8 Mbps downstream (CO to CPE): conforming TR048
Up to 8 PVC in UBR, CBR, VBRrt, VBRnrt
mode
Voice
Simultaneous voice calls
2
Analogue Interfaces
2xFXS RJ11 connectors
Dial tone supported: DTMF
Tones: customizable
Ringing voltage: 35 Vrms, Sine
wave
Ringing frequency: 25Hz default
(frequency
and
cadence
programmable
for
each
FXS
interface)
REN: 5 per FXS port
On-hook voltage: 48V nominal
Off-hook current: 22mA nominal
(other values programmable)
Terminating impendance: 600 Ohm
default
(other
impendances
programmable)
Loop signalling: Loop Start
Loop length: 200m max
VoIP Protocols
H.323 v4
Properties
Echo cancellation G.168
Silence suppression/comfort noise
generation
Modem/fax passthrough
Voice Codecs
G.711 Alaw/MiLaw, G.729A
Others
Autodetection of cut-over
Class 5 Services
Caller ID
V.23 Modem and DTMF transmitter on board
Data
Domestic LAN Interfaces
1 Ethernet 10/100 BaseT half/full duplex autonegotiating
1 USB port
RJ 45 connectors
Layer 3
NAT (RFC 1631)
RIP v1/RIP v2
Static Route
LLC/SNAP, VCMUX for bridged/
routed PDU's (RFC 2684/1483)
PPPoE (RFC 2516) max.5 PVC
PPPoA (RFC 2364)
IPoA
MER (a.k.a. IP over Ethernet over
AAL5)
ARP
DNS Relay
DNS server fallback in DNS relay
User authentication PAP (RFC 1334)
and CHAP (RFC 1994)
Others
DHCP Client/Server
TFTP Client
Management
Integrated Web Server
Upgradeable via Telnet, TFTP and
Web Server
Power Supply
12Vdc
±
15%, 10W Input Voltage 230Vac, 50Hz
Page 140 / 165
Telsey
telecommunications
Technical Features
MT500--SIEN12
132
Physical Dimensions
Width 150mm, Depth 140mm, Heigth 38mm. Wall mountable
Environmental Conditions
Operation temperature: 5°C to 45°C
Storage temperature: -5°C to 55°C
Operating humidity: 5% to 85% (not condensing)
Certifications
European Community Directive for Low Voltage Electrical Equipment 73/23/
EEC according to EN 60950
European Community Directive for Electromagnetic Compatibility EMC 89/336/
EEC according to EN55022 and EN55024

Rate

4 / 5 based on 1 vote.

Popular Telsey Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top